E1 Version
EMC	EU countries Australia	EN 55022: (1998): Class B (with shielded cable) EN55024 (1998) AS/NZS 3548 (1995)
Safety	EU countries Australia	EN 60950: (1992 + Amendments 1 to 4) TS 001 (1997)
Telecom	EU countries UK Other countries	CTR4 (ISDN PRI) CTR12 (E1 120 Ohm) NTR4 (E1 75 Ohm) Refer to the NMS web site (`www.nmss.com`).

Version

Appendix A

Hardware Specifications

: General
: Protocols
: Host Interface
: H.110 Compliant Interface
: Environment
: Power Requirements for AG 4000C/1600
: Power Requirements for AG 4000C/3200
: Power Requirements for AG 4000C/4800
: CEPT E1 G.703 Telephony Interface
: DSX-1 Telephony Interface
: Compliance and Regulatory Certification
: Standards

General

TDM Bus

Features one complete H.110 bus interface with MVIP-95 enhanced-compliant switching

DSP Processing Power

16, 32, or 48 TMS320C549 DSPs at 100 MIPS each.

Microprocessor

One 100 MHz 80486 compatible embedded processor

Software Development Kits

Natural Access for Windows NT, UnixWare, and Solaris

TDM Bus	Features one complete H.110 bus interface with MVIP-95 enhanced-compliant switching
DSP Processing Power	16, 32, or 48 TMS320C549 DSPs at 100 MIPS each.
Microprocessor	One 100 MHz 80486 compatible embedded processor
Software Development Kits	Natural Access for Windows NT, UnixWare, and Solaris

Protocols

Wink start MF/DTMF
DID
Loop start T1
Ground start T1
ISDN primary rate

Host Interface

Feature

Specification

Electrical

CompactPCI bus designed to CompactPCI PICMG specification revision 2.1

Mechanical

Designed to the CompactPCI PICMG specification revision 2.1 for 6U style cards

Bus Speed

DC to 33 MHz

Maximum Number of Boards per Chassis

1 - 14

Maximum Number of Ports per Chassis

Limited by host processor resources

Memory Mapped

Memory mapped interface for efficient block data transfers

Addresses/Interrupts

Address and interrupts automatically configured by CompactPCI BIOS (no jumpers or switches)

Feature	Specification
Electrical	CompactPCI bus designed to CompactPCI PICMG specification revision 2.1
Mechanical	Designed to the CompactPCI PICMG specification revision 2.1 for 6U style cards
Bus Speed	DC to 33 MHz
Maximum Number of Boards per Chassis	1 - 14
Maximum Number of Ports per Chassis	Limited by host processor resources
Memory Mapped	Memory mapped interface for efficient block data transfers
Addresses/Interrupts	Address and interrupts automatically configured by CompactPCI BIOS (no jumpers or switches)

H.110 Compliant Interface

Flexible connectivity between T1/E1 trunks, DSPs, and H.110 bus.
Switchable access to any of 4096 H.110 timeslots.
H.110 clock master or clock slave (software-selectable).
Compatible with any H.110-compliant telephony interface.

Environment

Feature

Description

Operating Temperature

0 to 50 degC

Storage Temperature

-20 to 70 degC

Humidity

5 to 80%, non-condensing

Feature	Description
Operating Temperature	0 to 50 degC
Storage Temperature	-20 to 70 degC
Humidity	5 to 80%, non-condensing

Power Requirements for AG 4000C/1600

State

Requirement

BD_SEL# Inactive/AG 4000C Inactive

230 mA maximum @ +5 V
107 mA maximum @ +3.3 V

BD_SEL# Active/AG 4000C in Reset

900 mA maximum @ +5 V
280 mA maximum @ 3.3 V

BD_SEL# Active/AG 4000C Active

1.5 A maximum @ 5 V
1.5 A @ 3.3 V

State	Requirement
BD_SEL# Inactive/AG 4000C Inactive	230 mA maximum @ +5 V 107 mA maximum @ +3.3 V
BD_SEL# Active/AG 4000C in Reset	900 mA maximum @ +5 V 280 mA maximum @ 3.3 V
BD_SEL# Active/AG 4000C Active	1.5 A maximum @ 5 V 1.5 A @ 3.3 V

Power Requirements for AG 4000C/3200

State

Requirement

BD_SEL# Inactive/AG 4000C Inactive

230 mA maximum @ +5 V
107 mA maximum @ +3.3 V

BD_SEL# Active/AG 4000C in Reset

1.2 mA maximum @ +5 V
600 mA maximum @ 3.3 V

BD_SEL# Active/AG 4000C Active

1.6 A maximum @ 5 V
2.0 A @ 3.3 V

State	Requirement
BD_SEL# Inactive/AG 4000C Inactive	230 mA maximum @ +5 V 107 mA maximum @ +3.3 V
BD_SEL# Active/AG 4000C in Reset	1.2 mA maximum @ +5 V 600 mA maximum @ 3.3 V
BD_SEL# Active/AG 4000C Active	1.6 A maximum @ 5 V 2.0 A @ 3.3 V

Power Requirements for AG 4000C/4800

State

Requirement

BD_SEL# Inactive/AG 4000C Inactive

230 mA maximum @ +5 V
107 mA maximum @ +3.3 V

BD_SEL# Active/AG 4000C in Reset

1.4 mA maximum @ +5 V
800 mA maximum @ 3.3 V

BD_SEL# Active/AG 4000C Active

1.8 A maximum @ 5 V
2.4 A @ 3.3 V

State	Requirement
BD_SEL# Inactive/AG 4000C Inactive	230 mA maximum @ +5 V 107 mA maximum @ +3.3 V
BD_SEL# Active/AG 4000C in Reset	1.4 mA maximum @ +5 V 800 mA maximum @ 3.3 V
BD_SEL# Active/AG 4000C Active	1.8 A maximum @ 5 V 2.4 A @ 3.3 V

CEPT E1 G.703 Telephony Interface

Interface

G.703 2048 Kbps trunk interface

Framing

CEPT G.703/G.704 Channel Associated Signaling

Signaling Capabilities

ABCD bits for Channel Associated Signaling and HDLC/LAPD for generating/terminating data link

Line Code

HDB3 (in zero code suppression) or AMI

Alarm Signal Capabilities

Loss of Frame Alignment (OOF), Loss of Signaling Multiframe Alignment and Loss of CRC Multiframe Alignment (red), Remote Alarm and Remote Multiframe Alarm (yellow), Alarm Indication Signal (AIS) (blue)

Counts

Bit error rate, CRC errors, slips, line code violations, far-end block errors

Loopback

Per channel and across channels under software control

Connectors

Up to four 75 Ohm RJ48C connnectors with BNC adapter cables or up to four 120 Ohm RJ48C connectors

Interface	G.703 2048 Kbps trunk interface
Framing	CEPT G.703/G.704 Channel Associated Signaling
Signaling Capabilities	ABCD bits for Channel Associated Signaling and HDLC/LAPD for generating/terminating data link
Line Code	HDB3 (in zero code suppression) or AMI
Alarm Signal Capabilities	Loss of Frame Alignment (OOF), Loss of Signaling Multiframe Alignment and Loss of CRC Multiframe Alignment (red), Remote Alarm and Remote Multiframe Alarm (yellow), Alarm Indication Signal (AIS) (blue)
Counts	Bit error rate, CRC errors, slips, line code violations, far-end block errors
Loopback	Per channel and across channels under software control
Connectors	Up to four 75 Ohm RJ48C connnectors with BNC adapter cables or up to four 120 Ohm RJ48C connectors

DSX-1 Telephony Interface

Interface

ANSI T1.102, T1.403

Framing

D4, ESF

Signaling Capabilities

ABCD bits for Channel Associated Signaling and HDLC/LAPD for generating/terminating data link

Line Codes

AMI or selectable B8ZS, jammed bit (ZCS) or no zero code suppression

Alarm Signal Capabilities

Yellow, Red, and Blue

Counts

Bipolar violation, F(t) error, and CRC error

Robbed bit

Selectable on a per-trunk basis

Loopback

Per channel and overall under software control. Automatic remote loopback with CSU option.

Connectors

Up to four RJ48C connectors

Interface	ANSI T1.102, T1.403
Framing	D4, ESF
Signaling Capabilities	ABCD bits for Channel Associated Signaling and HDLC/LAPD for generating/terminating data link
Line Codes	AMI or selectable B8ZS, jammed bit (ZCS) or no zero code suppression
Alarm Signal Capabilities	Yellow, Red, and Blue
Counts	Bipolar violation, F(t) error, and CRC error
Robbed bit	Selectable on a per-trunk basis
Loopback	Per channel and overall under software control. Automatic remote loopback with CSU option.
Connectors	Up to four RJ48C connectors

Compliance and Regulatory Certification

Natural MicroSystems obtains board-level approvals certificates for supported countries. In addition to the approval obtained by NMS for the board and its associated software, some countries require a system level approval before connecting the system to the public network. To learn what approvals you require, contact the appropriate regulatory authority in the target country T1 Version EMC US and Canada FCC Part 15, Subpart J (Class A with shielded cable) Safety Canada NRTL recognized to cUL, UL 1950, 3rd edition Telecom US Canada FCC Part 68 ISC CS-03 . : E1 Version EMC EU countries Australia EN 55022: (1998): Class B (with shielded cable) EN55024 (1998) AS/NZS 3548 (1995) Safety EU countries Australia EN 60950: (1992 + Amendments 1 to 4) TS 001 (1997) Telecom EU countries UK Other countries CTR4 (ISDN PRI) CTR12 (E1 120 Ohm) NTR4 (E1 75 Ohm) Refer to the NMS web site (www.nmss.com).

T1 Version
EMC	US and Canada	FCC Part 15, Subpart J (Class A with shielded cable)
Safety	Canada	NRTL recognized to cUL, UL 1950, 3rd edition
Telecom	US Canada	FCC Part 68 ISC CS-03

Standards

CompactPCI standards and specifications are maintained by the PCI Industrial Computers Manufacturers Group (PICMG). For CompactPCI information, contact: PICMG c/o Rogers Communications 401 Edgewater Place, Suite 500 Wakefield, MA 01880 Tel: 781-246-9318 Fax: 781-224-1239 Email: www.picmg.org

For GO-MVIP information, contact: GO-MVIP, Inc. 3220 N Street, NW, Suite 360 Washington, DC 20007 Tel: 800-NOW-MVIP (US and Canada) Tel: 903-769-3717; Fax: 903-769-3818 Email: info@mvip.org

For ECTF information, contact: ECTF 39355 California Street, Suite 307 Fremont, CA 94538 Tel: 501-608-5915 Fax: 510-608-5917 Email: ectf@ectf.org
For more information, refer to the following documents: This manual... Provides... CompactPCI Computer Telephony Specification PICMG 2.5 R1.0 Information about the telephony backplane in CompactPCI, available from PICMG. CompactPCI Specification PICMG 2.0 R2.1 Specification information about CompactPCI, available from PICMG. Enterprise Computer Telephony Forum H.110 Revision 1.0 Hardware Compatibility Specification: CT Bus Information about the H.110 telephony bus, available from ECTF. Hot Swap Specification PICMG 2.1 R1.0 Information about Hot Swap, available from PICMG. IEEE 1101.1, IEEE 1101.10, IEEE 1101.11 Mechanical specifications referenced in CompactPCI specifications.

This manual...	Provides...
CompactPCI Computer Telephony Specification PICMG 2.5 R1.0	Information about the telephony backplane in CompactPCI, available from PICMG.
CompactPCI Specification PICMG 2.0 R2.1	Specification information about CompactPCI, available from PICMG.
Enterprise Computer Telephony Forum H.110 Revision 1.0 Hardware Compatibility Specification: CT Bus	Information about the H.110 telephony bus, available from ECTF.
Hot Swap Specification PICMG 2.1 R1.0	Information about Hot Swap, available from PICMG.
IEEE 1101.1, IEEE 1101.10, IEEE 1101.11	Mechanical specifications referenced in CompactPCI specifications.

Version

Want to send us feedback on our documentation? Email: Tech_Pubs@nmss.com

Appendix A

Hardware Specifications

Protocols

H.110 Compliant Interface

Environment Feature Description Operating Temperature 0 to 50 degC Storage Temperature -20 to 70 degC Humidity 5 to 80%, non-condensing

Power Requirements for AG 4000C/1600 State Requirement BD_SEL# Inactive/AG 4000C Inactive 230 mA maximum @ +5 V 107 mA maximum @ +3.3 V BD_SEL# Active/AG 4000C in Reset 900 mA maximum @ +5 V 280 mA maximum @ 3.3 V BD_SEL# Active/AG 4000C Active 1.5 A maximum @ 5 V 1.5 A @ 3.3 V

Power Requirements for AG 4000C/3200 State Requirement BD_SEL# Inactive/AG 4000C Inactive 230 mA maximum @ +5 V 107 mA maximum @ +3.3 V BD_SEL# Active/AG 4000C in Reset 1.2 mA maximum @ +5 V 600 mA maximum @ 3.3 V BD_SEL# Active/AG 4000C Active 1.6 A maximum @ 5 V 2.0 A @ 3.3 V

Power Requirements for AG 4000C/4800 State Requirement BD_SEL# Inactive/AG 4000C Inactive 230 mA maximum @ +5 V 107 mA maximum @ +3.3 V BD_SEL# Active/AG 4000C in Reset 1.4 mA maximum @ +5 V 800 mA maximum @ 3.3 V BD_SEL# Active/AG 4000C Active 1.8 A maximum @ 5 V 2.4 A @ 3.3 V

Compliance and Regulatory Certification

Standards

Environment

Feature

Description

Operating Temperature

0 to 50 degC

Storage Temperature

-20 to 70 degC

Humidity

5 to 80%, non-condensing

Power Requirements for AG 4000C/1600

State

Requirement

BD_SEL# Inactive/AG 4000C Inactive

230 mA maximum @ +5 V
107 mA maximum @ +3.3 V

BD_SEL# Active/AG 4000C in Reset

900 mA maximum @ +5 V
280 mA maximum @ 3.3 V

BD_SEL# Active/AG 4000C Active

1.5 A maximum @ 5 V
1.5 A @ 3.3 V

Power Requirements for AG 4000C/3200

State

Requirement

BD_SEL# Inactive/AG 4000C Inactive

230 mA maximum @ +5 V
107 mA maximum @ +3.3 V

BD_SEL# Active/AG 4000C in Reset

1.2 mA maximum @ +5 V
600 mA maximum @ 3.3 V

BD_SEL# Active/AG 4000C Active

1.6 A maximum @ 5 V
2.0 A @ 3.3 V

Power Requirements for AG 4000C/4800

State

Requirement

BD_SEL# Inactive/AG 4000C Inactive

230 mA maximum @ +5 V
107 mA maximum @ +3.3 V

BD_SEL# Active/AG 4000C in Reset

1.4 mA maximum @ +5 V
800 mA maximum @ 3.3 V

BD_SEL# Active/AG 4000C Active

1.8 A maximum @ 5 V
2.4 A @ 3.3 V