(Page 1 of 3 in this chapter) Version

Appendix B

NMS Board Parameters

Introduction

: Default Parameters

Function Parameters

Trunk Control Program Parameters

: LPS 133
: WNK 137

: Configuring Transfer for Wink Start and Loop Start Protocols

Introduction

This appendix describes: Default Parameters Function Parameters Trunk Control Program Parameters Note: For detailed information about function parameters, refer to the ADI Service Function Reference Manual.

Default Parameters

The following table lists allowed and default Natural Access parameter settings for the TSP and WAVE driver. Parameter Allowed Values Default Set by TSP adi.play.DTMFAbort 0 0 adi.record.DTMFAbort 0 0 adi.start.callctl.eventmask 6 6 adi.start.callctl.debugmask 0, 1, 2 2 adi.lps.nodialtoneaction 0 or 2 2 adi.placecall.connectmask 0x0183 0x0183
To override these settings for a given TAPI application, call lineDevSpecific from the application as described in Section 5.2, Using lineDevSpecific. For instructions on how to make TAPI parameters take effect, refer to Section 5.1.1, Making Parameter Changes Take Effect.

Parameter	Allowed Values	Default Set by TSP
adi.play.DTMFAbort	`0`	`0`
adi.record.DTMFAbort	`0`	`0`
adi.start.callctl.eventmask	`6`	`6`
adi.start.callctl.debugmask	`0, 1, 2`	`2`
adi.lps.nodialtoneaction	`0 or 2`	`2`
adi.placecall.connectmask	`0x0183`	`0x0183`

Function Parameters

The following table lists the function parameters used by TAPI to control the behavior of their associated function calls. For a detailed discussion of parameter management in Natural Access, refer to the Natural Access Developer's Reference Manual, ADI Service Developer's Manual, or ADI Service Developer's Manual.

Function Parameter

Dependent TAPI Function

Dependent ADI Function

ADI.CALLPROG

lineGatherDigits

adiStartCallProgress

ADI.COLLECT

lineGatherDigits

adiCollectDigits

ADI.DIAL

None directly. However, adiStartDial is used to dial the prm.tsp.xfer.recallstrings after a consultation call has been disconnected.

adiStartDial

ADI.DTMF

lineGenerateDigits

adiStartDTMF

ADI.DTMFDETECT

None.

adiStartDTMFDetector

ADI.ENERGY

lineMonitorTones (only if monitoring for silence)

adiStartEnergyDetector

ADI.FSKRECEIVE

None.

adiStartReceivingFSK

ADI.FSKSEND

None.

adiStartSendingFSK

ADI.PLACECALL

lineMakeCall, lineSetupTransfer/lineDial (used in combination), lineBlindTransfer

adiPlaceCall, adiPlaceSecondCall, adiTransferCall

ADI.PLAY

waveOutReset

adiStartPlaying, adiPlayFromMemory, adiPlayAsync

ADI.RECORD

waveInStart

adiStartRecording, adiRecordToMemory, adiRecordAsync

ADI.START

lineOpen, lineMonitorTones

adiStartProtocol

ADI.TONE

lineGenerateTone

adiStartTones

ADI.TONEDETECT

lineMonitorTones

adiStartToneDetector

Function Parameter	Dependent TAPI Function	Dependent ADI Function
ADI.CALLPROG	lineGatherDigits	adiStartCallProgress
ADI.COLLECT	lineGatherDigits	adiCollectDigits
ADI.DIAL	None directly. However, adiStartDial is used to dial the prm.tsp.xfer.recallstrings after a consultation call has been disconnected.	adiStartDial
ADI.DTMF	lineGenerateDigits	adiStartDTMF
ADI.DTMFDETECT	None.	adiStartDTMFDetector
ADI.ENERGY	lineMonitorTones (only if monitoring for silence)	adiStartEnergyDetector
ADI.FSKRECEIVE	None.	adiStartReceivingFSK
ADI.FSKSEND	None.	adiStartSendingFSK
ADI.PLACECALL	lineMakeCall, lineSetupTransfer/lineDial (used in combination), lineBlindTransfer	adiPlaceCall, adiPlaceSecondCall, adiTransferCall
ADI.PLAY	waveOutReset	adiStartPlaying, adiPlayFromMemory, adiPlayAsync
ADI.RECORD	waveInStart	adiStartRecording, adiRecordToMemory, adiRecordAsync
ADI.START	lineOpen, lineMonitorTones	adiStartProtocol
ADI.TONE	lineGenerateTone	adiStartTones
ADI.TONEDETECT	lineMonitorTones	adiStartToneDetector

Trunk Control Program Parameters

The sections provide a list of protocol structures and shows the protocol and board combinations the protocol structures can be used with. All protocol parameters are used when the protocol is started. Protocols are started when the NMS TAPI function lineOpen is called if the Start Protocol checkbox is selected in the Advanced System-Level Configuration Dialog box.
For more information, refer to Section 5.2.3, Specifying lineOpen Behavior.
The following tables list the Trunk Control Program (TCP) parameters.

(Page 1 of 3 in this chapter) Version

Want to send us feedback on our documentation? Email: Tech_Pubs@nmss.com