AG-T1 and AG-E1 Installation and Developer's Manual

P/N 6207-15

Table of Contents

• About This Manual
• Organization of Material
• Related Documents
• Developer Support
• 1 Introduction
• 1.1 Introduction
• 1.2 About the AG-T1 and AG-E1
• 1.2.1 DSP Resources
• 1.2.2 ISA Bus and Trunk Connectivity
• 1.2.3 MVIP Connectivity
• 1.2.4 Daughterboard Interface
• 1.2.5 Hardware Variations
• 1.3 Software Components
• 1.3.1 About Trunk Control Programs (TCPs)
• 1.3.2 About CT Access and AG Access
• 1.3.3 About MVIP Switching Software
• 1.3.4 About agmon and the AG Configuration File
• 1.3.5 About Runfiles
• 1.4 Installation Summary
• 2 Installing an AG-T1 or AG-E1 Board
• 2.1 Introduction
• 2.2 Hardware Requirements
• 2.3 Configuring the Board's I/O Address Space
• 2.4 Setting the Interrupt
• 2.5 Installing the Hardware (No MVIP Connectivity)
• 2.6 Installing the Hardware (With MVIP Connectivity)
• 2.6.1 Installing Boards In Your System (With MVIP)
• 2.7 Completing Your Installation
• 2.8 Connecting an AG-T1 Board to the Network
• 2.8.1 Ordering T1 Service
• 2.8.2 Connecting to the T1 Trunk
• 2.9 Connecting An AG-E1 To The Network
• 2.10 Loopback Configurations
• 3 Editing The AG Configuration File
• 3.1 Introduction
• 3.2 Creating an AG Configuration File for Your Setup
• 3.2.1 Hardware- and Trunk-Specific Settings
• 3.2.2 Enabling MVIP Connectivity
• 3.3 Running agmon
• 3.4 Sample AG Configuration Files
• 3.4.1 Single AG-T1 Board, US CAS - Wink Start
• 3.4.2 Single AG-T1 Board, ISDN
• 3.4.3 Single AG-E1 Board, MFC-R2
• 3.4.4 AG-E1 and AG-8 Boards, MFC-R2, MVIP Connectivity
• 3.4.5 Two AG-T1 Boards, One AG-8 Board, ISDN
• 4 Verifying The Installation
• 4.1 Introduction
• 4.2 The Status Indicator LEDs
• 4.3 Verifying That Your Board Is Working Correctly
• 5 Trunk Channels and AG Boards
• 5.1 Introduction
• 5.2 Channels and Transmission Rates
• 5.3 Signaling
• 5.3.1 Channel-Associated Signaling (CAS)
• 5.3.2 Common Channel Signaling (CCS)
• 5.4 Framing
• 5.4.1 T1 Framing
• 5.4.2 E1 Framing
• 5.5 Voice Encoding
• 5.5.1 Companding
• 5.6 Alternate Mark Inversion, ZCS
• 6 MVIP Connectivity
• 6.1 Introduction
• 6.2 Trunk Channels and MVIP Timeslots
• 6.2.1 T1 Channels and MVIP Timeslots
• 6.2.2 E1 Channels and MVIP Timeslots
• 6.3 The AG-T1 and AG-E1 MVIP Switch Model
• 6.3.1 The AG-T1 and AG-E1 MVIP Switch Model (MVIP-95)
• 6.3.2 The AG-T1 and AG-E1 MVIP Switch Model (MVIP-90)
• 6.4 Default MVIP Connections If MVIP Switching
  Is Disabled
• 6.5 FMIC Switching Restrictions
• Appendix A: Glossary
• Appendix B: t1stat and e1stat
• Introduction
• t1stat and e1stat
• Usage
• Display
• Appendix C: Configuring the Sec8k Clock
• Introduction
• About the Sec8k Clock
• Configuring Sec8k
• Appendix D: Hardware Specifications
• General
• Host Interface
• Audio Signal Processing
• Tone Dialing
• Pulse Dialing (AG-T1)
• DTMF Tone Detection
• MF Tone Detection
• DSX-1 Telephony Interface (AG-T1)
• AG-T1 Compliance
• CEPT E1 G.703 Telephony Interface (AG-E1)
• AG-E1 Compliance
• MVIP Interface
• Index

Natural MicroSystems, Inc.
100 Crossing Boulevard
Framingham, MA 01702

Contact Developer Support