(Page 46 of 46 in this chapter) Version

ACU_USER_INFO_RQ

Purpose

Request user-to-user information. Note: This primitive is only implemented on the TE side (such as if your partner equipment equals EQUIPMENT_NT).

Conn_id

An allocated call.

Macro

Description

Q.931 IE

4ESS

E10

N12

DMS100

ETSI

VN6

HKG

AUSTEL1

NTT

KOREA

TAIWAN

QSIG

Acu_user_info_a_ext_parms

Pointer to buffer containing extended parameters.

(Not used.)

Acu_user_info_a_fac, Acu_user_info_fac_size
Filling order: 2

User facility information.

Facility

x

x

x

Acu_user_info_a_tsp_ie_list, Acu_user_info_tsp_ie_list_size
Filling order: 3

Pointer to (and size of) transparent IE buffer.

(Does not map to an IE.)

x

x

x

x

x

x

Acu_user_info_a_uui, Acu_user_info_uui_size
Filling order: 1

Pointer to (and size of) ISDN user-to-user information (optional).

User-User

x

x

x

x

x

Acu_user_info_ext_parms_lgth

Total length of buffer containing extended parameters.

(Not used.)

Acu_user_info_ext_parms_nb

Number of parameters in buffer containing extended parameters.

(Not used.)

Acu_user_info_fac_protocol_discr

User facility protocol discriminator.

(Not used.)

Acu_user_info_uui_protocol

UUI protocol discriminator value. (See Section 8.3.8 for a list of valid values.) Default: UUI_IA5 (UUI_USER_SPF for HKG variant)

User-User

x

x

x

x

Note: Address parameters must be set in the order indicated in the table. If one of them is unused, its size field must be set to 0.

8.3 Data Types and Constants In Primitives

8.3.1 User Rate Values

The following values specify the user rate in ACU_CONN_IN, ACU_CONN_RQ, ACU_CONN_RS, and ACU_SETUP_REPORT_IN messages.
These values are defined in isdnacu.h. Rate Description ACU_RA_50 0.050 kbits/s CCITT V.6 and X.1 ACU_RA_75 0.075 kbits/s CCITT V.6 and X.1 ACU_RA_75_1200 0.075/1.2 kbits/s CCITT V.6 and x.1 ACU_RA_100 0.100 kbits/s CCITT V.6 and X.1 ACU_RA_110 0.110 kbits/s CCITT V.6 and X.1 ACU_RA_134 0.1345 kbits/s CCITT X.1 ACU_RA_150 0.150 kbits/s CCITT V.6 and X.1 ACU_RA_200 0.200 kbits/s CCITT V.6 and X.1 ACU_RA_300 0.300 kbits/s CCITT V.6 and X.1 ACU_RA_600 0.6 kbits/s CCITT V.6 and x.1 ACU_RA_1200 1.2 kbits/s CCITT V.6 ACU_RA_1200_75 1.2/0.075 kbits/s CCITT V.6 and x.1 ACU_RA_2400 2.4 kbits/s CCITT V.6 and X.1 ACU_RA_3600 3.6 kbits/s CCITT V.6 ACU_RA_4800 4.8 kbits/s CCITT V.6 and x.1 ACU_RA_7200 7.2 kbits/s CCITT V.6 ACU_RA_8000 8 kbits/s CCITT I.460 ACU_RA_9600 9.6 kbits/s CCITT V.6 and x.1 ACU_RA_12000 12 kbits/s CCITT V.6 ACU_RA_14400 14.4 kbits/s CCITT V.6 ACU_RA_16000 16 kbits/s CCITT I.460 ACU_RA_19200 19.2 kbits/s CCITT V.6 ACU_RA_32000 32 kbits/s CCITT I.460 ACU_RA_38400 38.4 kbits/s extended V.14 ACU_RA_38400_NO_ETSI 38.4 kbits/s extended V.14 (VN3) NON ETSI ACU_RA_48000 48 kbits/s CCITT V.6 and X.1 ACU_RA_56000 56 kbits/s CCITT V.6 ACU_RA_57600 57.6 kbits/s extended V.14 (VN3) NON ETSI NON CCITT ACU_RA_64000 64 kbits/s CCITT I.460

Rate	Description
ACU_RA_50	0.050 kbits/s CCITT V.6 and X.1
ACU_RA_75	0.075 kbits/s CCITT V.6 and X.1
ACU_RA_75_1200	0.075/1.2 kbits/s CCITT V.6 and x.1
ACU_RA_100	0.100 kbits/s CCITT V.6 and X.1
ACU_RA_110	0.110 kbits/s CCITT V.6 and X.1
ACU_RA_134	0.1345 kbits/s CCITT X.1
ACU_RA_150	0.150 kbits/s CCITT V.6 and X.1
ACU_RA_200	0.200 kbits/s CCITT V.6 and X.1
ACU_RA_300	0.300 kbits/s CCITT V.6 and X.1
ACU_RA_600	0.6 kbits/s CCITT V.6 and x.1
ACU_RA_1200	1.2 kbits/s CCITT V.6
ACU_RA_1200_75	1.2/0.075 kbits/s CCITT V.6 and x.1
ACU_RA_2400	2.4 kbits/s CCITT V.6 and X.1
ACU_RA_3600	3.6 kbits/s CCITT V.6
ACU_RA_4800	4.8 kbits/s CCITT V.6 and x.1
ACU_RA_7200	7.2 kbits/s CCITT V.6
ACU_RA_8000	8 kbits/s CCITT I.460
ACU_RA_9600	9.6 kbits/s CCITT V.6 and x.1
ACU_RA_12000	12 kbits/s CCITT V.6
ACU_RA_14400	14.4 kbits/s CCITT V.6
ACU_RA_16000	16 kbits/s CCITT I.460
ACU_RA_19200	19.2 kbits/s CCITT V.6
ACU_RA_32000	32 kbits/s CCITT I.460
ACU_RA_38400	38.4 kbits/s extended V.14
ACU_RA_38400_NO_ETSI	38.4 kbits/s extended V.14 (VN3) NON ETSI
ACU_RA_48000	48 kbits/s CCITT V.6 and X.1
ACU_RA_56000	56 kbits/s CCITT V.6
ACU_RA_57600	57.6 kbits/s extended V.14 (VN3) NON ETSI NON CCITT
ACU_RA_64000	64 kbits/s CCITT I.460

8.3.2 Service Values

The following values specify the service in ACU_CONN_CO, ACU_CONN_IN, ACU_CONN_RQ, ACU_CONN_RS, ACU_FACILITY_IN, ACU_FACILITY_RQ, ACU_RESUME_CO, ACU_RESUME_RQ, and ACU_SETUP_REPORT_IN messages.
These values are defined in isdnval.h. Service Description FAX_SERVICE Call for G3 facsimile service FAX_4_SERVICE Call for G4 facsimile service DATA_SERVICE Call for "data" service DATA_GCI_SERVICE Call for "data" service on GCI bus DATA_56KBS_SERVICE Call for "data at 56 KBS" service RAW_DATA_SERVICE Call for "raw data" service on GCI bus: no MPH_B_INIT_RQ is generated (no B channel driver is associated) DATA_TRANS_SERVICE Call for transparent data service MODEM_SERVICE Call for modem data service AUDIO_7_SERVICE Call for 7khz Audio service X25_SERVICE Call for X.25 circuit-mode service X25_PACKET_SERVICE Call for X.25 packet-mode service VOICE_SERVICE Call for voice service VOICE_GCI_SERVICE Call for voice service on GCI bus RAW_TELEPHONY_SERVICE Call for "raw telephony" service on GCI bus: no MPH_B_INIT_RQ generated (no B channel driver is associated) VOICE_TRANS_SERVICE Call for transparent voice service V110_SERVICE Call for V.110 service V120_SERVICE Call for V.120 service VIDEO_SERVICE Call for VIDEO service TDD_SERVICE Call for TDD service DATA_H0_SERVICE Call for data using H0 (384kbs) channel service (PRI only) DATA_H11_SERVICE Call for data using H11 (1536kbs) channel service DATA_H12_SERVICE Call for data using H12 (1536kbs) channel service DATA_MULTIRATE_SERVICE Call for data using Multirate (2..30x64kbs) channel service DATA_128KBS_SERVICE Call for data using 2x64kbs channel service (BRI only) NO_B_CHAN_SERVICE Call for no B channel service (bearer-independent calls - QSIG only) FAX_RELAY_SERVICE Call for G3 facsimile service (for use with "Physical Relay" process) DATA_RELAY_SERVICE Call for "data" service (for use with "Physical Relay" process) DATA_56KBS_RELAY_SERVICE Call for "data at 56 KBS" service (for use with 'Physical Relay' process) DATA_TRANS_RELAY_SERVICE Call for data transparent service (for use with "Physical Relay" process) MODEM_RELAY_SERVICE Call for modem data service (for use with "Physical Relay" process) X25_RELAY_SERVICE Call for X.25 circuit-mode service (for use with "Physical Relay" process) VOICE_RELAY_SERVICE Call for voice service (for use with "Physical Relay" process) VOICE_GCI_RELAY_SERVICE Call for voice service on GCI bus (for use with "Physical Relay" process) NO_SERVICE Undefined service

Service	Description
FAX_SERVICE	Call for G3 facsimile service
FAX_4_SERVICE	Call for G4 facsimile service
DATA_SERVICE	Call for "data" service
DATA_GCI_SERVICE	Call for "data" service on GCI bus
DATA_56KBS_SERVICE	Call for "data at 56 KBS" service
RAW_DATA_SERVICE	Call for "raw data" service on GCI bus: no MPH_B_INIT_RQ is generated (no B channel driver is associated)
DATA_TRANS_SERVICE	Call for transparent data service
MODEM_SERVICE	Call for modem data service
AUDIO_7_SERVICE	Call for 7khz Audio service
X25_SERVICE	Call for X.25 circuit-mode service
X25_PACKET_SERVICE	Call for X.25 packet-mode service
VOICE_SERVICE	Call for voice service
VOICE_GCI_SERVICE	Call for voice service on GCI bus
RAW_TELEPHONY_SERVICE	Call for "raw telephony" service on GCI bus: no MPH_B_INIT_RQ generated (no B channel driver is associated)
VOICE_TRANS_SERVICE	Call for transparent voice service
V110_SERVICE	Call for V.110 service
V120_SERVICE	Call for V.120 service
VIDEO_SERVICE	Call for VIDEO service
TDD_SERVICE	Call for TDD service
DATA_H0_SERVICE	Call for data using H0 (384kbs) channel service (PRI only)
DATA_H11_SERVICE	Call for data using H11 (1536kbs) channel service
DATA_H12_SERVICE	Call for data using H12 (1536kbs) channel service
DATA_MULTIRATE_SERVICE	Call for data using Multirate (2..30x64kbs) channel service
DATA_128KBS_SERVICE	Call for data using 2x64kbs channel service (BRI only)
NO_B_CHAN_SERVICE	Call for no B channel service (bearer-independent calls - QSIG only)
FAX_RELAY_SERVICE	Call for G3 facsimile service (for use with "Physical Relay" process)
DATA_RELAY_SERVICE	Call for "data" service (for use with "Physical Relay" process)
DATA_56KBS_RELAY_SERVICE	Call for "data at 56 KBS" service (for use with 'Physical Relay' process)
DATA_TRANS_RELAY_SERVICE	Call for data transparent service (for use with "Physical Relay" process)
MODEM_RELAY_SERVICE	Call for modem data service (for use with "Physical Relay" process)
X25_RELAY_SERVICE	Call for X.25 circuit-mode service (for use with "Physical Relay" process)
VOICE_RELAY_SERVICE	Call for voice service (for use with "Physical Relay" process)
VOICE_GCI_RELAY_SERVICE	Call for voice service on GCI bus (for use with "Physical Relay" process)
NO_SERVICE	Undefined service

8.3.3 Number Type Values

These values specify the calling, called, and redirecting number type in ACU_CONN_IN, ACU_SETUP_REPORT_IN, and ACU_ALERT_IN messages.
These values are defined in isdnval.h. Type Description N_TYPE_UNKNOWN (Default for all variants except 4ESS, VN6) Unknown N_TYPE_INTERNATIONAL International number N_TYPE_NATIONAL (Default for 4ESS and VN6 variants) National number N_TYPE_NET_SPF Network specific number N_TYPE_SUBSCRIBER Subscriber number N_TYPE_LOCAL AT5 local (directory) number N_TYPE_ABBREVIATED Abbreviated number

Type	Description
N_TYPE_UNKNOWN (Default for all variants except 4ESS, VN6)	Unknown
N_TYPE_INTERNATIONAL	International number
N_TYPE_NATIONAL (Default for 4ESS and VN6 variants)	National number
N_TYPE_NET_SPF	Network specific number
N_TYPE_SUBSCRIBER	Subscriber number
N_TYPE_LOCAL	AT5 local (directory) number
N_TYPE_ABBREVIATED	Abbreviated number

8.3.4 Plan Values

These values specify the calling, called, and redirecting number plan in ACU_ALERT_IN, ACU_CONN_IN, ACU_CONN_RQ, and ACU_SETUP_REPORT_IN messages.
These values are defined in isdnval.h. Plan Description N_PLAN_UNKNOWN (Default for all variants except VN6) Unknown N_PLAN_ISDN (Default for VN6 and AusTel variants) ISDN/telephony numbering plan (CCITT E.164/E.163). N_PLAN_TELEPHONE Telephony - not in CEPT N_PLAN_DATA Data n. Plan (CCITT x.121) N_PLAN_TELEX Telex n. Plan (CCITT f.69) N_PLAN_NATIONAL National standard numbering plan N_PLAN_PRIVATE Private numbering plan

Plan	Description
N_PLAN_UNKNOWN (Default for all variants except VN6)	Unknown
N_PLAN_ISDN (Default for VN6 and AusTel variants)	ISDN/telephony numbering plan (CCITT E.164/E.163).
N_PLAN_TELEPHONE	Telephony - not in CEPT
N_PLAN_DATA	Data n. Plan (CCITT x.121)
N_PLAN_TELEX	Telex n. Plan (CCITT f.69)
N_PLAN_NATIONAL	National standard numbering plan
N_PLAN_PRIVATE	Private numbering plan

8.3.5 Screening Indicator Values

These values specify the calling and redirecting number screeening indicator in ACU_ALERT_IN, ACU_ALERT_RQ, ACU_CONN_IN, ACU_CONN_RQ, and ACU_SETUP_REPORT_IN messages.
These values are defined in isdnval.h. Screening Indicator Description N_SCREEN_USER_PROVIDED (Default) User-provided, not screened N_SCREEN_USER_PASSED (Default for AusTel) User-provided, verified, and passed N_SCREEN_USER_FAILED User-provided, verified, and failed N_SCREEN_NETWORK_PROVIDED Network provided

Screening Indicator	Description
N_SCREEN_USER_PROVIDED (Default)	User-provided, not screened
N_SCREEN_USER_PASSED (Default for AusTel)	User-provided, verified, and passed
N_SCREEN_USER_FAILED	User-provided, verified, and failed
N_SCREEN_NETWORK_PROVIDED	Network provided

8.3.6 Redirecting Reason Values

These values specify the redirecting reason in ACU_ALERT_IN, ACU_CONN_CO, ACU_CONN_IN, ACU_CONN_RQ, and ACU_SETUP_REPORT_IN messages.
These values are defined in isdnval.h. Redirecting Reason Description REASON_UNKNOWN (Default) Unknown REASON_CALL_FORWARDING_BUSY Call forwarding busy REASON_CALL_FORWARDING_NO_REPLY Call forwarding no reply REASON_CALL_FORWARDING_DTE_OUT Call forwarding DTE out of order REASON_CALL_FORWARDING_BY_CALLED Call forwarding by called equipment REASON_CALL_TRANSFER Call transfer REASON_CALL_PICKUP Call pickup REASON_CALL_FORWARDING_UNCONDITIONAL Call forwarding unconditional

Redirecting Reason	Description
REASON_UNKNOWN (Default)	Unknown
REASON_CALL_FORWARDING_BUSY	Call forwarding busy
REASON_CALL_FORWARDING_NO_REPLY	Call forwarding no reply
REASON_CALL_FORWARDING_DTE_OUT	Call forwarding DTE out of order
REASON_CALL_FORWARDING_BY_CALLED	Call forwarding by called equipment
REASON_CALL_TRANSFER	Call transfer
REASON_CALL_PICKUP	Call pickup
REASON_CALL_FORWARDING_UNCONDITIONAL	Call forwarding unconditional

8.3.7 Location Values

These values specify the location in ACU_ALERT_IN, ACU_ALERT_RQ, ACU_CALL_PROC_IN, ACU_CALL_PROC_RQ, ACU_CLEAR_IN, ACU_CONN_IN, ACU_CONN_RQ, ACU_PROGRESS_IN, ACU_PROGRESS_RQ, and ACU_SETUP_REPORT_IN messages.
These values are defined in isdnval.h.

Location

Description

LOC_USER (Default if partner_equip argument passed to isdnStartProtocol is EQUIPMENT_NT)

User

LOC_PR_LOCAL_USER

Private network serving the local user

LOC_NETWORK (Default if partner_equip argument passed to isdnStartProtocol is EQUIPMENT_TE)

Location network (SWD)

LOC_TRANSIT_NET

Transit network

LOC_PU_REMOTE_USER

Public network serving the remote user

LOC_PR_REMOTE_USER

Private network serving the remote user

BEYOND_IWP (Default for DMS100 variant)

Network beyond interworking point

Location	Description
LOC_USER (Default if *partner_equip* argument passed to isdnStartProtocol is EQUIPMENT_NT)	User
LOC_PR_LOCAL_USER	Private network serving the local user
LOC_NETWORK (Default if *partner_equip* argument passed to isdnStartProtocol is EQUIPMENT_TE)	Location network (SWD)
LOC_TRANSIT_NET	Transit network
LOC_PU_REMOTE_USER	Public network serving the remote user
LOC_PR_REMOTE_USER	Private network serving the remote user
BEYOND_IWP (Default for DMS100 variant)	Network beyond interworking point

8.3.8 UUI Protocol Discriminator Values

These values specify the UUI protocol discriminator in ACU_ALERT_RQ, ACU_CLEAR_CO, ACU_CLEAR_RQ, ACU_CLEAR_RS, ACU_CONN_CO, ACU_CONN_IN, ACU_CONN_RQ, ACU_CONN_RS, ACU_SETUP_REPORT_ IN, ACU_USER_INFO_IN, and ACU_USER_INFO_RQ messages.
These values are defined in isdnval.h. UUI Protocol Discriminator Description UUI_USER_SPF (Default for HKG variant) User specific coding UUI_OSI OSI UUI_X244 Rec. X.244 UUI_SYSTEM_MANAGEMENT Reserved for system management convergence function UUI_IA5 (Default) IA5 characters (ASCII) UUI_V120 Rec. V.120 UUI_Q931 Rec. Q.931

UUI Protocol Discriminator	Description
UUI_USER_SPF (Default for HKG variant)	User specific coding
UUI_OSI	OSI
UUI_X244	Rec. X.244
UUI_SYSTEM_MANAGEMENT	Reserved for system management convergence function
UUI_IA5 (Default)	IA5 characters (ASCII)
UUI_V120	Rec. V.120
UUI_Q931	Rec. Q.931

8.3.9 Signal Values

These values specify the signal in ACU_ALERT_IN, ACU_ALERT_RQ, ACU_CALL_PROC_IN, ACU_CLEAR_IN, ACU_CLEAR_RQ, ACU_CONN_CO, ACU_INFORMATION_IN, ACU_INFORMATION_RQ, and ACU_PROGRESS_IN messages.
These values are defined in isdnval.h. Signal Value Description ACUDIAL_ON Dial tone on ACURING_BACK_ON Ring back tone on ACUNET_CONGEST_ON Network congest tone on ACUBUSY_ON Busy tone on ACUTONES_OFF Tones off ACUALERTING_OFF Alerting off ACUCREDIT_CARD_TONE_ON Credit card tone on ACUOUT_OF_RANGE_TONE_ON Out of range tone on ACUQUEUING_TONE_ON Queuing tone on ACUAUDIBLE_TONE_ON Audible tone on ACUVISUAL_ALERT_1_ON Visual alert #1 on ACUVISUAL_ALERT_2_ON Visual alert #2 on ACUSATCOM_CALL_NOTIFY SATCOM call notify

Signal Value	Description
ACUDIAL_ON	Dial tone on
ACURING_BACK_ON	Ring back tone on
ACUNET_CONGEST_ON	Network congest tone on
ACUBUSY_ON	Busy tone on
ACUTONES_OFF	Tones off
ACUALERTING_OFF	Alerting off
ACUCREDIT_CARD_TONE_ON	Credit card tone on
ACUOUT_OF_RANGE_TONE_ON	Out of range tone on
ACUQUEUING_TONE_ON	Queuing tone on
ACUAUDIBLE_TONE_ON	Audible tone on
ACUVISUAL_ALERT_1_ON	Visual alert #1 on
ACUVISUAL_ALERT_2_ON	Visual alert #2 on
ACUSATCOM_CALL_NOTIFY	SATCOM call notify

8.3.10 Network-Provided Clearing Cause Values

These values specify the network-provided clearing cause in ACU_CLEAR_CO, ACU_CLEAR_IN, ACU_RESUME_CO, and ACU_SUSPEND_CO messages.
These values depend upon the variant. A list of values, derived from various specifications, is defined in decisdn.h, and is provided in the following table: Network-Provided Clearing Cause Description CAU_UNALL Unallocated number CAU_NOR_STN No route to transit network CAU_NOR_D No route to destination CAU_CH_UNACC Channel unnacceptable CAU_AWARD Call awarded and delivered in an established channel CAU_NORMAL_CC Normal call clearing CAU_BUSY User busy CAU_NO_USER_RES No user responding CAU_NO_ANSW No answer from user CAU_REJ Call rejected CAU_NUM_CHANGED Number changed CAU_NON_SEL Non-selected user clearing CAU_DEST_OOF Destination out of order CAU_INV Invalid number format CAU_FAC_REJ Facility rejected CAU_RES_TO_SE Response to STATUS ENQUIRY CAU_NORMAL_UNSPEC Normal, unspecified CAU_NO_CIRC_CHAN No circuit/channel available CAU_NET_OOF Network out of order CAU_TEMP_FAIL Temporary failure CAU_CONG Switching equipment congestion CAU_ACC_INF_DISC Access information discarded CAU_NOT_AVAIL Requested circuit/channel not available CAU_RES_UNAVAIL Resource unavailable CAU_QOF_UNAVAIL Quality of service unavailable CAU_FAC_NOT_SUB Requested facility not subscribed CAU_BC_NOT_AUT Bearer capability not authorized CAU_BC_NOT_AVAIL Bearer capability not presently available CAU_SERV_NOTAVAIL Service or option not available CAU_BC_NOT_IMP Bearer capability not implemented CAU_CHT_NOT_IMP Channel type not implemented CAU_FAC_NOT_IMP Requested facility not implemented CAU_RESTR_BC Only restricted digital bearer capability is available CAU_SERV_NOT_IMP Service or option not implemented CAU_INV_CRV Invalid call reference value CAU_CH_NOT_EX Identified channel does not exist CAU_CALL_ID_NOT_EX Call identity does not exist CAU_CALL_ID_IN_USE Call identity in use CAU_NO_CALL_SUSP No call suspended CAU_CALL_CLEARED The call has been cleared CAU_INCOMP_DEST Incompatible destination CAU_INV_TN Invalid transit network selection CAU_INV_MSG Invalid message CAU_MAND_IE_MISSING Mandatory information element is missing CAU_MSGT_NOT_EX Message type not existent/implemented CAU_MSG_NOT_COMP Message not compatible with call state or message type not existent CAU_IE_NOT_EX Information element not existent/implemented CAU_INV_IE_CONTENTS Invalid information element contents CAU_MSG_NOT_COMP_CS Message not compatible with call state CAU_RECOVERY Recovery on timer expiration CAU_PROTO_ERR Protocol error CAU_INTERW Interworking CAU_PREEMPTION Preemption (5ESS) CAU_PREEMPTION_CRR Preemption, circuit reserved for reuse (5ESS) CAU_PREC_CALL_BLK Precedence call blocked (5ESS) CAU_BC_INCOMP_SERV Bearer capability incompatible with service request (5ESS) CAU_OUT_CALLS_BARRED Outgoing calls barred (4ESS, 5ESS) CAU_SERV_VIOLATED Service operation violated (5ESS) CAU_IN_CALLS_BARRED Incoming calls barred (DMS, 4ESS, 5ESS) CAU_DEST_ADD_MISSING Destination address missing and direct call not subscribed (DMS) CAU_RESTART Call clearing due to restart procedure CAU_TIMER_300 Call clearing due to internal timer 300 expiration CAU_TIMER_302 Call clearing due to internal timer 302 expiration CAU_TIMER_303 Call clearing due to internal timer 303 expiration CAU_TIMER_304 Call clearing due to internal timer 304 expiration CAU_TIMER_308 Call clearing due to internal timer 308 expiration CAU_TIMER_309 Call clearing due to internal timer 309 expiration CAU_TIMER_310 Call clearing due to internal timer 310 expiration CAU_TIMER_316 Call clearing due to internal timer 316 expiration CAU_TIMER_317 Call clearing due to internal timer 317 expiration CAU_TIMER_318 Call clearing due to internal timer 318 expiration CAU_TIMER_319 Call clearing due to internal timer 319 expiration CAU_TIMER_399 Call clearing due to internal timer 399 expiration

Network-Provided Clearing Cause	Description
CAU_UNALL	Unallocated number
CAU_NOR_STN	No route to transit network
CAU_NOR_D	No route to destination
CAU_CH_UNACC	Channel unnacceptable
CAU_AWARD	Call awarded and delivered in an established channel
CAU_NORMAL_CC	Normal call clearing
CAU_BUSY	User busy
CAU_NO_USER_RES	No user responding
CAU_NO_ANSW	No answer from user
CAU_REJ	Call rejected
CAU_NUM_CHANGED	Number changed
CAU_NON_SEL	Non-selected user clearing
CAU_DEST_OOF	Destination out of order
CAU_INV	Invalid number format
CAU_FAC_REJ	Facility rejected
CAU_RES_TO_SE	Response to STATUS ENQUIRY
CAU_NORMAL_UNSPEC	Normal, unspecified
CAU_NO_CIRC_CHAN	No circuit/channel available
CAU_NET_OOF	Network out of order
CAU_TEMP_FAIL	Temporary failure
CAU_CONG	Switching equipment congestion
CAU_ACC_INF_DISC	Access information discarded
CAU_NOT_AVAIL	Requested circuit/channel not available
CAU_RES_UNAVAIL	Resource unavailable
CAU_QOF_UNAVAIL	Quality of service unavailable
CAU_FAC_NOT_SUB	Requested facility not subscribed
CAU_BC_NOT_AUT	Bearer capability not authorized
CAU_BC_NOT_AVAIL	Bearer capability not presently available
CAU_SERV_NOTAVAIL	Service or option not available
CAU_BC_NOT_IMP	Bearer capability not implemented
CAU_CHT_NOT_IMP	Channel type not implemented
CAU_FAC_NOT_IMP	Requested facility not implemented
CAU_RESTR_BC	Only restricted digital bearer capability is available
CAU_SERV_NOT_IMP	Service or option not implemented
CAU_INV_CRV	Invalid call reference value
CAU_CH_NOT_EX	Identified channel does not exist
CAU_CALL_ID_NOT_EX	Call identity does not exist
CAU_CALL_ID_IN_USE	Call identity in use
CAU_NO_CALL_SUSP	No call suspended
CAU_CALL_CLEARED	The call has been cleared
CAU_INCOMP_DEST	Incompatible destination
CAU_INV_TN	Invalid transit network selection
CAU_INV_MSG	Invalid message
CAU_MAND_IE_MISSING	Mandatory information element is missing
CAU_MSGT_NOT_EX	Message type not existent/implemented
CAU_MSG_NOT_COMP	Message not compatible with call state or message type not existent
CAU_IE_NOT_EX	Information element not existent/implemented
CAU_INV_IE_CONTENTS	Invalid information element contents
CAU_MSG_NOT_COMP_CS	Message not compatible with call state
CAU_RECOVERY	Recovery on timer expiration
CAU_PROTO_ERR	Protocol error
CAU_INTERW	Interworking
CAU_PREEMPTION	Preemption (5ESS)
CAU_PREEMPTION_CRR	Preemption, circuit reserved for reuse (5ESS)
CAU_PREC_CALL_BLK	Precedence call blocked (5ESS)
CAU_BC_INCOMP_SERV	Bearer capability incompatible with service request (5ESS)
CAU_OUT_CALLS_BARRED	Outgoing calls barred (4ESS, 5ESS)
CAU_SERV_VIOLATED	Service operation violated (5ESS)
CAU_IN_CALLS_BARRED	Incoming calls barred (DMS, 4ESS, 5ESS)
CAU_DEST_ADD_MISSING	Destination address missing and direct call not subscribed (DMS)
CAU_RESTART	Call clearing due to restart procedure
CAU_TIMER_300	Call clearing due to internal timer 300 expiration
CAU_TIMER_302	Call clearing due to internal timer 302 expiration
CAU_TIMER_303	Call clearing due to internal timer 303 expiration
CAU_TIMER_304	Call clearing due to internal timer 304 expiration
CAU_TIMER_308	Call clearing due to internal timer 308 expiration
CAU_TIMER_309	Call clearing due to internal timer 309 expiration
CAU_TIMER_310	Call clearing due to internal timer 310 expiration
CAU_TIMER_316	Call clearing due to internal timer 316 expiration
CAU_TIMER_317	Call clearing due to internal timer 317 expiration
CAU_TIMER_318	Call clearing due to internal timer 318 expiration
CAU_TIMER_319	Call clearing due to internal timer 319 expiration
CAU_TIMER_399	Call clearing due to internal timer 399 expiration

8.3.11 Clear Code Values

These values specify the clear code in ACU_CLEAR_CO and ACU_CLEAR_IN messages.
These values are defined in isdnacu.h. Clear Code Description ACURC_BUSY Busy ACURC_NOPROCEED No proceed indication (dial tone) ACURC_NOANSWER No answer ACURC_NOAUTOANSWER No auto-answer tone detected ACURC_CONGESTED GSTN or system is congested ACURC_INCOMING Incoming call detected while trying to dial ACURC_NOLINE Wrong addressing info, or context already used ACURC_ERRNUM Errored number ACURC_INHNUM Inhibited number ACURC_2MNUM Too many errored/inhibited numbers ACURC_HUNGUP Remote has hung up or incident on connection ACURC_NETWORK_ERROR Network has disconnected ACURC_TIMEOUT Timeout error ACURC_BAD_SERVICE Bad service ID in ACU_CONN_RQ/RS ACURC_INTERNAL Other internal error

Clear Code	Description
ACURC_BUSY	Busy
ACURC_NOPROCEED	No proceed indication (dial tone)
ACURC_NOANSWER	No answer
ACURC_NOAUTOANSWER	No auto-answer tone detected
ACURC_CONGESTED	GSTN or system is congested
ACURC_INCOMING	Incoming call detected while trying to dial
ACURC_NOLINE	Wrong addressing info, or context already used
ACURC_ERRNUM	Errored number
ACURC_INHNUM	Inhibited number
ACURC_2MNUM	Too many errored/inhibited numbers
ACURC_HUNGUP	Remote has hung up or incident on connection
ACURC_NETWORK_ERROR	Network has disconnected
ACURC_TIMEOUT	Timeout error
ACURC_BAD_SERVICE	Bad service ID in ACU_CONN_RQ/RS
ACURC_INTERNAL	Other internal error

8.3.12 Facility Code Values

These values specify the facility code in ACU_FACILITY_RQ, ACU_FACILITY_IN, and ACU_FACILITY_RQ messages.
These values are defined in isdnacu.h. Facility Code Description ACU_FAC_CALL_FORWARDING Premise transfer ACU_FAC_CALL_DEFLECTION Terminal transfer ACU_FAC_CHARGING Charging ACU_FAC_CHARGING_TOTAL Charging total cost ACU_FAC_HOLD Call hold ACU_FAC_RETRIEVE Call retrieve ACU_FAC_ALTERNATE To and from facility ACU_FAC_TRF Transfer ACU_FAC_THREE_PARTY Conferencing ACU_FAC_MALICIOUS_CALL_ID Malicious call identification ACU_FAC_RECALL Recall facility (ETSI) ACU_FAC_TRANSPARENT Transparent facility for CC&NS ACU_FAC_CALL_APPEAR Call appearence request ACU_FAC_FEATURE_ACT Feature activation request ACU_FAC_DROP Drop call ACU_FAC_FEATURE_IND Feature indication (NT->TE only) ACU_FAC_PCS_USER_ONLY Send PCS-user information only, with no other facility request. Only for VN6, within ACU_FACILITY_RQ. (See Appendix D for more information on this IE)

Facility Code	Description
ACU_FAC_CALL_FORWARDING	Premise transfer
ACU_FAC_CALL_DEFLECTION	Terminal transfer
ACU_FAC_CHARGING	Charging
ACU_FAC_CHARGING_TOTAL	Charging total cost
ACU_FAC_HOLD	Call hold
ACU_FAC_RETRIEVE	Call retrieve
ACU_FAC_ALTERNATE	To and from facility
ACU_FAC_TRF	Transfer
ACU_FAC_THREE_PARTY	Conferencing
ACU_FAC_MALICIOUS_CALL_ID	Malicious call identification
ACU_FAC_RECALL	Recall facility (ETSI)
ACU_FAC_TRANSPARENT	Transparent facility for CC&NS
ACU_FAC_CALL_APPEAR	Call appearence request
ACU_FAC_FEATURE_ACT	Feature activation request
ACU_FAC_DROP	Drop call
ACU_FAC_FEATURE_IND	Feature indication (NT->TE only)
ACU_FAC_PCS_USER_ONLY	Send PCS-user information only, with no other facility request. Only for VN6, within ACU_FACILITY_RQ. (See Appendix D for more information on this IE)

8.3.13 Action Code Values

These values specify the action code in ACU_FACILITY_IN, ACU_SET_MODE_CO, ACU_SET_MODE_RQ, ACU_TEST_CO, and ACU_TEST_RQ messages.
These values are defined in isdnacu.h. Action Code Description ACU_RQ_ACTIVATE Activate or register action ACU_RQ_CLEAR Deactivate or clear action ACU_RQ_ENQUIRY Enquiry action ACU_IN_TX Transmission ACU_CO_ACK Acknowledgement ACU_CO_REJ Reject

Action Code	Description
ACU_RQ_ACTIVATE	Activate or register action
ACU_RQ_CLEAR	Deactivate or clear action
ACU_RQ_ENQUIRY	Enquiry action
ACU_IN_TX	Transmission
ACU_CO_ACK	Acknowledgement
ACU_CO_REJ	Reject

8.3.14 Mode Code Values

These values specify the mode code in the Acu_set_mode_code macro in ACU_SET_MODE_RQ messages.
These values are defined in isdnacu.h. Code Description ACU_MODE_NA_OUT_OF_ORDER Allow/forbid calls on NAI given by R_msg_nai. ACU_MODE_CALL_OUT_OF_ORDER Allow/forbid calls on NAI/CONN_ID given by R_msg_nai/R_msg_conn_id. ACU_MODE_CHANI_OUT_OF_ORDER Allow/forbid usage of the B channel given by Acu_set_mode_data_chani. ACU_MODE_ALL_NA_OUT_OF_ORDER Allow/forbid calls on all NAIs.

Code	Description
ACU_MODE_NA_OUT_OF_ORDER	Allow/forbid calls on NAI given by R_msg_nai.
ACU_MODE_CALL_OUT_OF_ORDER	Allow/forbid calls on NAI/CONN_ID given by R_msg_nai/R_msg_conn_id.
ACU_MODE_CHANI_OUT_OF_ORDER	Allow/forbid usage of the B channel given by Acu_set_mode_data_chani.
ACU_MODE_ALL_NA_OUT_OF_ORDER	Allow/forbid calls on all NAIs.

8.3.15 Error Cause Values

These values specify the error code in the Acu_err_in_cause macro in ACU_ERR_IN messages.
These values are defined in isdnacu.h. Cause Code Description ACUER_PRIMITIVE_CODE Unknown primitive code ACUER_PARAM_VAL Invalid parameter ACUER_MANDATORY_PARAM_MISSING Mandatory parameter missing ACUER_PARAM_TYPE Incorrect parameter type ACUER_PARAM_LGTH Incorrect parameter length ACUER_UNEXPECTED_PRIMITIVE Unexpected primitive ACUER_PRIMITIVE_NOT_IMPLEMENTED SSDU primitive not implemented ACUER_NO_TIMER_AVAILABLE No more space to allocate new timer cells ACUER_CONGESTION Resource congestion

Cause Code	Description
ACUER_PRIMITIVE_CODE	Unknown primitive code
ACUER_PARAM_VAL	Invalid parameter
ACUER_MANDATORY_PARAM_MISSING	Mandatory parameter missing
ACUER_PARAM_TYPE	Incorrect parameter type
ACUER_PARAM_LGTH	Incorrect parameter length
ACUER_UNEXPECTED_PRIMITIVE	Unexpected primitive
ACUER_PRIMITIVE_NOT_IMPLEMENTED	SSDU primitive not implemented
ACUER_NO_TIMER_AVAILABLE	No more space to allocate new timer cells
ACUER_CONGESTION	Resource congestion

8.3.16 Progress Description Values

These values specify the progress description in ACU_ALERT_IN, ACU_ALERT_RQ, ACU_CALL_PROC_IN, ACU_CALL_PROC_RQ, ACU_CLEAR_IN, ACU_CONN_IN, ACU_CONN_RQ, ACU_PROGRESS_IN, ACU_PROGRESS_RQ, and ACU_SETUP_REPORT_IN messages.
These values are defined in isdnval.h. Progress Description Description NO_PROGRESS_DESCR No progress information to be stored PROGRESS_DESCR_NON_END_TO_ END_ISDN Call is not end-to-end ISDN; further call progress information may be available PROGRESS_DESCR_CALL_RETURNED_ISDN Call has returned to the ISDN PROGRESS_DESCR_IN_BAND_NOW In-band information or appropriate pattern now available

Progress Description	Description
NO_PROGRESS_DESCR	No progress information to be stored
PROGRESS_DESCR_NON_END_TO_ END_ISDN	Call is not end-to-end ISDN; further call progress information may be available
PROGRESS_DESCR_CALL_RETURNED_ISDN	Call has returned to the ISDN
PROGRESS_DESCR_IN_BAND_NOW	In-band information or appropriate pattern now available

8.3.17 Charging Type Values

These values specify the charging type in ACU_CLEAR_CO, ACU_CLEAR_IN, ACU_CLEAR_RQ, ACU_CLEAR_RS, ACU_CONN_CO, ACU_CONN_RS, ACU_INFORMATION_IN, and ACU_INFORMATION_RQ messages.
These values are defined in isdnacu.h. Charging Type Description ACUCHARG_TYPE_FREE_OF_CHARGE Free of charge (N/A in VN6/FRANCE) ACUCHARG_TYPE_CHARGE_ON_DURATION Charge on duration (N/A in VN6/FRANCE) ACUCHARG_TYPE_CHARGE_ON_ANSWER Charge on answer (N/A in VN6/FRANCE) ACUCHARG_TYPE_CHARGE_INCREMENT Charge increment (N/A in VN6/FRANCE) ACUCHARG_TYPE_SUB_TOTAL_CHARGE Sub-total charge ACUCHARG_TYPE_TOTAL_CHARGE Total charge

Charging Type	Description
ACUCHARG_TYPE_FREE_OF_CHARGE	Free of charge (N/A in VN6/FRANCE)
ACUCHARG_TYPE_CHARGE_ON_DURATION	Charge on duration (N/A in VN6/FRANCE)
ACUCHARG_TYPE_CHARGE_ON_ANSWER	Charge on answer (N/A in VN6/FRANCE)
ACUCHARG_TYPE_CHARGE_INCREMENT	Charge increment (N/A in VN6/FRANCE)
ACUCHARG_TYPE_SUB_TOTAL_CHARGE	Sub-total charge
ACUCHARG_TYPE_TOTAL_CHARGE	Total charge

8.3.18 Endpoint ID Values

These values are defined in isdnacu.h. Endpoint ID Description ACU_ACTION_NO_ENDPOINT_ID Do not send any endpoint ID (ACU_CONN_RQ) ACU_ACTION_SND_USID SPID was OK, send the endpoint ID info ACU_ACTION_NO_SPID_NEGOTIATION SPID negotiation is not supported ACU_ACTION_INVALID_SPID The received SPID is wrong ACU_ACTION_PROMPT_INFO Need a SPID from the terminal ACU_INTERPRETER_0 Terminal is selected if it is assigned the indicated TID and USID value ACU_INTERPRETER_1 Terminal is selected if it is NOT assigned the indicated TID but is assigned the indicated USID value

Endpoint ID	Description
ACU_ACTION_NO_ENDPOINT_ID	Do not send any endpoint ID (ACU_CONN_RQ)
ACU_ACTION_SND_USID	SPID was OK, send the endpoint ID info
ACU_ACTION_NO_SPID_NEGOTIATION	SPID negotiation is not supported
ACU_ACTION_INVALID_SPID	The received SPID is wrong
ACU_ACTION_PROMPT_INFO	Need a SPID from the terminal
ACU_INTERPRETER_0	Terminal is selected if it is assigned the indicated TID and USID value
ACU_INTERPRETER_1	Terminal is selected if it is NOT assigned the indicated TID but is assigned the indicated USID value

8.4 LAPD Primitives

The following table summarizes supported LAPD primitives: Message Type Description DL_DA_IN Indicates that a packet of acknowledged data has been received by the trunk from the remote party. DL_DA_RQ Sent by the application to the NMS ISDN protocol stack to request the stack to transmit a packet of acknowledged data. DL_EST_CO Indicates that equipment on the remote side of the ISDN trunk has acknowledged a SABME message sent by the ISDN protocol stack, and has sent back a UA message indicating that the data link is established. DL_EST_IN Indicates that a SABME message has been received by the NMS ISDN protocol stack. The stack automatically acknowledges the message by sending back a UA message, and establishes the data link. DL_EST_RQ Sent by the application to the NMS ISDN protocol stack to request the stack to establish a data link. The stack transmits a SABME message over the trunk. DL_REL_IN If the NMS ISDN software is in the IDLE state, this message indicates that an establishment request sent by the NMS ISDN protocol stack was not successfully answered. If the software is in the DATA_LINK_ESTABLISHED state, this message indicates that the data link has been broken. DL_U_DA_IN Indicates that a packet of unacknowledged data has been received by the trunk from the remote party. DL_U_DA_RQ Sent by the application to the NMS ISDN protocol stack to request the stack to transmit a packet of unacknowledged data.

Message Type	Description
DL_DA_IN	Indicates that a packet of acknowledged data has been received by the trunk from the remote party.
DL_DA_RQ	Sent by the application to the NMS ISDN protocol stack to request the stack to transmit a packet of acknowledged data.
DL_EST_CO	Indicates that equipment on the remote side of the ISDN trunk has acknowledged a SABME message sent by the ISDN protocol stack, and has sent back a UA message indicating that the data link is established.
DL_EST_IN	Indicates that a SABME message has been received by the NMS ISDN protocol stack. The stack automatically acknowledges the message by sending back a UA message, and establishes the data link.
DL_EST_RQ	Sent by the application to the NMS ISDN protocol stack to request the stack to establish a data link. The stack transmits a SABME message over the trunk.
DL_REL_IN	If the NMS ISDN software is in the IDLE state, this message indicates that an establishment request sent by the NMS ISDN protocol stack was not successfully answered. If the software is in the DATA_LINK_ESTABLISHED state, this message indicates that the data link has been broken.
DL_U_DA_IN	Indicates that a packet of unacknowledged data has been received by the trunk from the remote party.
DL_U_DA_RQ	Sent by the application to the NMS ISDN protocol stack to request the stack to transmit a packet of unacknowledged data.

(Page 46 of 46 in this chapter) Version

Want to send us feedback on our documentation? Email: Tech_Pubs@nmss.com

Macro	Description	Q.931 IE	4ESS	ETSI	VN6	NTT	KOREA	TAIWAN
Acu_user_info_a_ext_parms	Pointer to buffer containing extended parameters.	(Not used.)
Acu_user_info_a_fac, Acu_user_info_fac_size Filling order: 2	User facility information.	Facility		x			x	x
Acu_user_info_a_tsp_ie_list, Acu_user_info_tsp_ie_list_size Filling order: 3	Pointer to (and size of) transparent IE buffer.	(Does not map to an IE.)	x	x	x	x	x	x
Acu_user_info_a_uui, Acu_user_info_uui_size Filling order: 1	Pointer to (and size of) ISDN user-to-user information (optional).	User-User		x	x	x	x	x
Acu_user_info_ext_parms_lgth	Total length of buffer containing extended parameters.	(Not used.)
Acu_user_info_ext_parms_nb	Number of parameters in buffer containing extended parameters.	(Not used.)
Acu_user_info_fac_protocol_discr	User facility protocol discriminator.	(Not used.)
Acu_user_info_uui_protocol	UUI protocol discriminator value. (See Section 8.3.8 for a list of valid values.) Default: UUI_IA5 (UUI_USER_SPF for HKG variant)	User-User		x	x		x	x