(Page 2 of 2 in this chapter)

Introduction

This appendix documents the AG board and driver error messages.
agmon displays the error messages on the screen and writes to the AG error log file. The AG error log file is:
NT and OS/2: .\agerror.log
UnixWare, SCO and Solaris: /var/opt/nms/ag/agerror.log
agmon error messages are formatted as follows:

Board errors that are specific to an active line will be sent to running applications in the ADIEVN_BOARD_ERROR message instead of appearing on the agmon screen.
The ADIEVN_BOARD_ERROR message contains the following: value field, low 16 bits error code (shown in decimal) value field, high 16 bits error type (shown in hex) size field, low word first word of additional data size field, high word second word of additional data

The following is a compilation of error messages generated by AG board firmware. Type 8000 and 8100 Error Code Error Name Additional Information -1 NO_SUCH_MSGTYP Illegal message code -2 NO_PROCESSORS_BOOTED On DSP boot, no DSPs booted -3 SMALL_BUFS_NO_MEM Not enough system memory for small buffer pool -4 SMALL_BUFS_NO_CREATE Creation of small buffer pool failed -5 LARGE_BUFS_NO_MEM Not enough system memory for large buffer pool -6 LARGE_BUFS_NO_CREATE Creation of large buffer pool failed -7 NO_MEM_BUF_AVAILABLE Not enough system memory for allocation request -8 CANT_FREE_MEM_BUF Failure to free memory buffer or area -9 AMX_RSRC_INIT_FAIL Failure to initialize AMX resource -10 TPROC_NUM_OUT_OF_RANGE Task processor number out of range -11 TPROC_ALREADY_INIT Task processor already initialized -12 TPCB_MEM_ALLOC_FAIL Failure to allocate task proc memory in driver -13 TLIST_CMEM_ALLOC_FAIL Failure to allocate task list memory in CMEM -14 TPROC_WILL_NOT_INIT Task processor failed to initialize -15 OCB_MEM_ALLOC_FAIL Failure to allocate OCB memory in DSP driver -16 OVLY_DUPLICATE_IDS Different overlays have same ID -17 OVLY_ALREADY_LOADED Overlay is already loaded into driver memory -18 OVLY_MEM_ALLOC_FAIL Failure to allocate memory for overlay in driver -19 CANT_FREE_OVLY_BUF Failure to free buffer passing overlay -20 OVLY_NOT_FOUND Overlay ID not found in OCB list -21 CANT_FREE_OVLY_BLOCK Failure to free overlay cleared from driver -22 OVLY_NOT_IN_DRIVER Overlay not in driver for downloading to CMEM -23 OVLY_ALREADY_IN_CMEM Overlay is already downloaded to CMEM -24 OVLY_WONT_FIT_IN_CMEM Failure to allocate overlay space in CMEM -25 OVLY_NOT_IN_CMEM Overlay is not currently in CMEM -26 CANT_FREE_CMEM_OVLY Failure to free overlay space in CMEM -27 OVLY_IDCHK_BAD Overlay ID in CMEM doesn't match that in driver -28 OVLY_ALREADY_CLEARED Overlay is already cleared from CMEM -29 TPROC_NOT_YET_INIT Task processor not yet initialized -30 CANT_LOAD_DEFAULT_OVLY Task processor failed to load default overlay -31 CANT_FREEZE_CMEM Failure to freeze CMEM and allocate dynamic blocks -32 NO_MVIP_CNF_ACTIVE Neither MVIP config block is active -33 MVIP_PROCESSOR_ERROR MVIP processor is reporting an error -34 TASK_PROCESSOR_ERROR A task processor is reporting an error -35 BOOT_EXTRA_BUF_PROBLEM Can't allocate memory check buffer on DSP booting -36 BOOT_CMEM_CHECK_ERROR CMEM memory test failure on DSP booting -37 SMALL_BUFS_NO_REINIT Failure to reinitialize small buffer pool -38 LARGE_BUFS_NO_REINIT Failure to reinitialize large buffer pool -39 PORT_ALREADY_OPEN Port is already open -40 PORT_IN_USE Port can't be closed until not in use -41 STREAM_NOT_AVAILABLE Selected MVIP stream is not now active -42 PORTS_IN_USE Can't select other MVIP stream set when ports open -43 CHANNEL_ALREADY_OPEN No more channels available -44 unused -45 NO_MEM_FOR_CCB Failure to allocate memory for CCB -46 CHANNEL_WAKE_MSG_FAIL Wakeup message to channel task failed -47 CHANNEL_NUM_OUT_OF_RANGE Channel number is out of range -48 CHANNEL_ALREADY_CLOSED Channel is already closed -49 CHANNEL_LIST_NOT_EMPTY Can't close until all channel lists are empty -50 CHANNEL_ABORT_MSG_FAIL Channel abort message failed -51 CANT_FREE_CCB_MEM Failure to free CCB memory -52 FDB_BUFFER_SIZE_ERROR FDB buffer size and internal size info conflict -53 FDB_DUPLICATE_IDS Two FDB's have the same ID -54 FDB_MEM_ALLOC_FAIL Failure to allocate memory for the FDB -55 CANT_FREE_FDB_BUF Failure to free buffer passing FDB -56 PORT_NOT_OPEN Can't assign port until open -57 SCB_ALLOC_FAIL Failure to allocate buffer for SCB -58 PORT_ALREADY_ALLOCATED Output port is already assigned -59 INPUT_PORT_INDEX_COLLISION No other output port assigned for forking -60 PORT_NOT_IN_USE Can't release a port not open -61 PORT_NOT_OWNED_OR_IDLE Can't release a port either not owned or in use -62 CANT_FREE_SCB Failure to free SCB memory buffer -63 CHANNEL_NOT_OPEN Request to channel not currently open -64 INPUT_BUF_ALLOC_FAIL Can't allocate input buffer for direct connect -65 STREAM_BUF_ALLOC_FAIL Can't allocate CMEM stream buf for direct connect -66 PORT_NOT_CONNECTED Port is not direct connected -67 CANT_FREE_STREAM_BUF Can't free CMEM stream buf on disconnect -68 CANT_FREE_INPUT_BUF Can't free input buffer on disconnect -69 CANT_FREE_OUTPUT_BUF Can't free output buffer on disconnect -70 CANT_FIND_PORT_SCB Port SCB missing on disconnect -71 CANT_SEND_EVENT Failure to send event message to channel task -72 CANT_RELEASE_BUFFER Failure to free down buffer when empty -73 CANT_REPORT_BUF_DONE Failure to report buffer done to channel task -74 CONTINUATION_BUF_ALLOC_FAIL Failure to allocate next up buffer when needed -75 CANT_PASS_BUFFER Failure to pass up buffer to channel task -76 OUTPUT_BUF_QUEUE_OVERFLOW Too many downward buffers submitted -77 CANT_FIND_FDB FDB ID not found in list -78 WRONG_NMBR_PARMS_PASSED Wrong number parms passed on function start -79 TVB_ALLOC_FAIL Failure to allocate task variable block in CMEM -80 CANT_FREE_PARM_BUFFER Failure to free buffer passing function parms -81 CANT_ALLOC_SFCB Failure to allocate SCB for function -82 NO_INPUT_PORT_FOR_FUNC Function needs input port not in LIFO -83 CANT_ALLOC_STREAM_BUF Can't allocate stream buffer for func in CMEM -84 CANT_FREE_SPCB Can't free SCB buffer used in LIFO -85 NO_OUTPUT_PORT_FOR_FUNC Function needs output port not in LIFO -86 CANT_ALLOC_S3CB Can't allocate SCB for coprocessor stream -87 NOT_ENOUGH_BUFFERS_PASSED Not enough buffers were passed to start function -88 CANT_ALLOC_INPUT_BUF Failure to allocate input buf on function start -89 PASSED_BUFFERS_LEFT_OVER Buffers were left over on function start -90 CANT_FREE_PASSED_BUF Can't free down buf on function stop -91 CANT_ALLOC_SPCB Can't allocate SCB for LIFO on function stop -92 CANT_FREE_SFCB Can't free function SCB on function stop -93 CANT_FREE_S3CB Can't free coprocessor SCB on function stop -94 FCB_FOR_DIFFERENT_CHANNEL Channel number in FCB is wrong -95 CANT_FREE_FCB Failure to free FCB buffer on function stop -96 TL_OVLY_NOT_IN_CMEM Overlay not in CMEM when list building needs it -97 TL_OVLY_NOT_LOADED Overlay not in task processor when list build -98 TL_BUILD_LIST_OVERFLOW Added list piece overflowed temp build area -99 TL_OVERLAY_NOT_FOUND Overlay not in OCB list when needed -100 TL_OVERLAY_NOT_IN_CMEM Overlay not in CMEM when needed -101 TL_PROC_NOT_FOUND No task processor can run requested function -102 TL_REM_FUNC_NOT_FOUND Function to stop doesn't own any list entries -103 TL_REM_NO_EOL Function owns past end of task list -104 TL_REM_BAD_LOAD_FORMAT Overlay load list format bad -105 TL_REM_TOO_MANY_SEPS Bad list structure found -106 CANT_ALLOC_FCB Can't allocate FCB buffer on function start -107 CANT_FIND_FCB Can't find FCB in list on function stop -108 COMMAND_STREAM_BUSY Command already queued when a second is issued -109 COMMAND_TOO_BIG More parms passed in command than in cmd stream -110 NO_COMMAND_STREAM Command given with no associated active stream -111 CANT_REPORT_BUF_STARTED Report of up buffer on function startup failed -112 INPUT_BUF_QUEUE_OVERFLOW Too many buf size values passed on func startup -113 CANT_FREE_TVB_BUF Can't free TVB in CMEM on function stop -114 PORT_FOR_IDLE_NOT_FOUND On change idle command, port not found -115 OVERFLOW_10MS_STREAMS Not all 10mS events and bufs in time -116 DB_PORT_NOT_IDLE DB port already connected on conn req -117 DB_NOT_MVIP_CONNECTED DB port not of MVIP type on disconnect -118 DB_PORT_NUM_TOO_BIG DB port num argument passed too big -119 DB_PORT_NOT_IDLE_CHAN On discon from chan, slot not idle -120 DB_PORT_WRONG_CHAN On disconnect, channel number wrong -121 DB_PORT_WRONG_INDEX On disconnect, index doesn't match -122 DB31_DEMUX_TASK_NOT_DONE Demux semaphore not set on 10mS period -123 DB31_MUX_TASK_NOT_DONE Mux semaphore not set on 10mS period -124 NO_SPACE_READING_DRV_STRUCT Buffer too small to get driver struct -125 WRONG_NUM_OVLYS_ASSIGNED Too many or no default ovly given TP -126 LIST_TOO_HIGH_IN_CMEM TP list allocated into MPROC code area -127 CMEM_TIMED_OUT -128 FMIC_ERROR FMIC or MVIP clock error -129 UNEXEPECTED_DB_INTERRUPT DB31 hardware access blocked by DSP -130 TASK_PROCESSOR_NOT_READY DSP overloaded or crashed -131 BAD_EVENT_FORMAT Mail message from DB31 has bad format -132 READ_STRUCT_BUF_TOO_SMALL
Type 8200 Error Code Error Name Additional Information -513 BAD_HOST_COMMAND_SEM -514 BAD_HOST_CMD_BUF_CNT -515 CANT_GET_HOST_CMD_BUF -516 CNT_POST_HCMD_TO_SUP -517 CANT_POST_HCMD_TO_CH -518 CANT_WAIT_HOST_EVENT -519 BAD_HOST_EVENT_SEM -520 CANT_CHANGE_EVENT_PRI -521 CANT_FREE_EVENT_BUF -522 CANT_ATTACH_MORE_MGRS -523 CANT_FIND_MANAGER_ID -524 MANAGER_NOT_ATTACHED -525 UNPROCESSED_MESSAGE -526 CANT_SEND_HOST_MSG -527 CANT_SEND_MSG_TO_CHAN -528 HCMD_CHANNEL_NOT_OPEN -529 CANT_GET_TASK_STACK -530 CHAN_TASK_CREATE_ERROR -531 CANT_REPORT_START_CHAN -532 CANT_SET_CHAN_TERM -533 NO_CH_TSKS_AVAILABLE -534 CHAN_ALREADY_STOPPED -535 CANT_KILL_CHAN_TASK -536 CANT_DELETE_CHAN_TASK -537 CANT_SIGNAL_HOST_EVENT -538 CANT_CREATE_CHAN_TIMER -539 CANT_DELETE_CHAN_TIMER -540 CANT_FREE_TASK_STACK -541 MGR_ALREADY_ATTACHED -542 CHANNEL_OUT_OF_RANGE -543 FATAL_FAULT_OR_TRAP Parms: 1=trap#, 2,3=location, 4-15= eax-edx,esi,edi -544 AMX_FATAL_EXIT Parm: AMX fatal exit code. -545 DEST_CHANNEL_NOT_OPEN -546 CANT_ALLOC_CONTEXTS Mem alloc failed -547 DB31_TOKEN_NOT_GRANTED db31 hardware access blocked by DSP -548 DB31_BAD_MAIL_MESSAGE mail message from DB31 has bad format
Type 8400 Error Code Error Name Additional Information 1024 GTPERR_MGR04_NOT_CONFIGURED START_MANAGER given before CONFIGURE_MGR 1025 GTPERR_BAD_ENGINE_REV TCP requires different GTP Engine rev 1026 GTPERR_BAD_CHANNEL_NUMBER Bad channel number 1027 GTPERR_BAD_TCP_NAME Bad TCP 1028 GTPERR_BAD_BUFFER_COUNT Bad number of buffers passed 1029 GTPERR_BAD_BUFFER_SIZE Inconsistent buffer size 1030 GTPERR_BAD_PARAMETER_COUNT Bad parameter count 1031 GTPERR_BAD_PARAMETER_INDEX Bad parameter index 1032 GTPERR_PARAM_INIT_ERROR Cannot init parameter (out of range) 1033 GTPERR_TOO_MANY_TCPS Too many 1034 GTPERR_CANNOT_ALLOCATE_TCP Cannot allocate TCP memory 1035 GTPERR_CANNOT_FREE_TCP Cannot deallocate TCP memory Type 8500 Error Code Error Name Additional Information 1280 TCPERR_BAD_ENGINE_STATE Incorrect engine state 1281 TCPERR_BAD_ENGINE_OFFSET Bad engine offset 1282 TCPERR_BAD_STATE_RECORD_ID Incorrect state record ID 1283 TCPERR_BAD_STATE_NUMBER Bad state number 1284 TCPERR_BAD_STATE_INDEX Bad state index 1285 TCPERR_BAD_PARAMETER_COUNT Bad parameter count 1286 TCPERR_BAD_PARAMETER_INDEX Bad parameter index 1287 TCPERR_BAD_TCP_INDEX Bad TCP index 1288 TCPERR_BAD_RECORD_SIZE Bad record size 1289 TCPERR_BAD_FUNCTION_ORDINAL Bad service function ordinal 1290 TCPERR_BAD_SERVICE_ARG_LIST Bad service argument list 1291 TCPERR_BAD_SERVICE_NO_ARGUM Bad number of service arguments 1292 TCPERR_BAD_ARGUMENT_TYPE Bad argument type 1293 TCPERR_BAD_TCP_NAME Bad TCP name 1294 TCPERR_TIMER_CREATION_ERROR Timer cannot be allocated 1295 TCPERR_TIMER_INDEX_ERROR Timer index is too large 1296 TCPERR_TOO_MANY_REPLIES Too many replies used in TCP 1297 TCPERR_TCP_NOT_RUNNING TCP is has not been started 1298 TCPERR_BAD_STATE_0_FUNC Bad svc within State#0 initialization 1299 TCPERR_CANNOT_FALL_THROUGH Bad ON statement to fall through 1300 TCPERR_GTP_COMMAND_IGNORED Unexpected command to GTP 1301 TCPERR_BAD_FUNC_IN_TRGREC Bad svc within trigger record 1302 TCPERR_BAD_FUNC_IN_STATE Bad svc within state initialization 1303 TCPERR_BAD_FUNC_IN_SUBR Bad svc within subroutine initialization 1304 TCPERR_INVALID_TRGREC_ID Invalid trigger record ID 1321 TCPERR_INVALID_REC_ID_SIZE Invalid record id_size 1322 TCPERR_SUBR_ON_NOT_FOUND Subroutine ON statement not found 1323 TCPERR_BAD_SERVICE_RETURN SVC mgr returned an error code 1324 TCPERR_INVALID_TOKEN_INDEX Request to access token out of range 1325 TCPERR_ILLEGAL_BRANCH Request to branch out of range 1328 TCPERR_CANNOT_ALLOC_MEM Cannot allocate AMX memory 1329 TCPERR_FUNC_CANNOT_RESTART Cannot start an already running func 1330 TCPERR_FUNC_NOT_STARTED Cannot stop a not running function 1331 TCPERR_BAD_SVC_ARG_VALUE Incorrect argument value in svc routine 1332 TCPERR_BAD_BUFFER_COUNT Bad buffer count 1342 TCPERR_BAD_SVC_RETURN Service routine returned a bad code 1343 TCPERR_CANNOT_REPLY_ASYNC Cannot use REPLY on ASYNC events
Type 8a00 Error Code Error Name -1024 FMICERR_LIBRARY_NOT_USABLE -1025 FMICERR_LIBRARY_INITIALIZED -1026 FMICERR_LOCK_CREATION_FAILED -1027 FMICERR_LOCK_FAILED -1028 FMICERR_UNLOCK_FAILED -1029 FMICERR_DELAY_FAILED -1030 FMICERR_INTERNAL_MACRO -1031 FMICERR_CONNECT_REFERENCE_CNT -1032 FMICERR_INVALID_LOCAL_DEVICE -1033 FMICERR_INVALID_STREAM -1034 FMICERR_INVALID_TIMESLOT -1035 FMICERR_INVALID_CLOCK_PARM -1036 FMICERR_INVALID_MODE -1037 FMICERR_INVALID_PARAMETER -1038 FMICERR_NO_PATH -1039 FMICERR_SWITCH_VERIFY_FAILED -1040 FMICERR_CONNECT_NOT_SUPPORTED -1041 FMICERR_MODE_NOT_SUPPORTED
Type 8d00 Error Code Error Name Additional Information 1 AGV_ERROR_UNSUPPORTED_CMD cmd, 0 2 AGV_ERROR_UNSUPPORTED_MODE command, data 3 AGV_ERROR_COMMAND_NOT_IMPL command 4 AGV_ERROR_WRONG_BUF_COUNT command, bcnt 5 AGV_ERROR_WRONG_PARM_COUNT command, pcnt 6 AGV_ERROR_UNEXPECTED_CMD command, cur function 7 AGV_ERROR_UNEXPECTED_EVENT msgtyp, parm0 8 AGV_ERROR_ACTIVE_FUNCTION command, state 9 AGV_ERROR_DRVAPI_ERROR DSP err, cmd 10 AGV_ERROR_SVC_ERROR SVC err, cmd 11 AGV_ERROR_TIMER_FAIL return code, 0/1/2 12 AGV_ERROR_EVENT4WRONGFUNC msg function, cur state 13 AGV_ERROR_UNEXPECTED_BUFF state 14 AGV_ERROR_BUFFER_OVERRUN buf count 15 AGV_ERROR_WRONG_BUFFER_DIR 16 AGV_ERROR_INTERNAL_ERROR error number 17 AGV_ERROR_MEMALLOC cmd, error code 18 AGV_ERROR_MGR_NOT_INIT cmd, 0 19 AGV_ERROR_INVALID_PARM cmd, parmval 20 AGV_ERROR_DSP_SERVICE cmd, errval 21 AGV_ERROR_DIGTIMING_ACTIVE cmd, 0 22 AGV_ERROR_FUNC_NOT_AVAIL cmd, 0 Type 9100 Error Code Error Name Additional Information 4353 SVCERR_INVALID_ARG Invalid arg value passed 4354 SVCERR_NUM_OF_ARGS Invalid number of args 4355 SVCERR_FUNC_NOT_STARTED Can't modify inactive func 4356 SVCERR_CANNOT_RESTART Can't restart active func 4357 SVCERR_TIMER_CREATE_ERROR Error creating timers 4358 SVCERR_TIMER_ERROR Error using timing services 4359 SVCERR_MEMORY_ALLOC Error doing mem alloc 4360 SVCERR_ACCESS_DENIED Function is locked 4361 SVCERR_FUNC_NOT_AVAILABLE Function not loaded/avail 4362 SVCERR_DRV_API_RESOURCE Func failed,missed resource 4386 SVCERR_DRV_API_ERROR DSP driver error.
Type FF00 - OS/2 Only Error Code Error Name Additional Information 1 AGERR_LOCKFAILED 21 AGERR_IDLECHANNEL channel, msgtyp 22 AGERR_MSGBALANCELOST channel, msgtyp 42 AGERR_LESSTHAN48BYTES SRAM words left 43 AGERR_RECVMSGCOUNT count left, next loc 44 AGERR_SRAM_STATE state 45 AGERR_BADCHANNEL channel, msgtyp 46 AGERR_MSGSNOTSENT qid, count left 47 AGERR_BADMGHDR 81 AGERR_SENDQEMPTY 82 AGERR_BADQTYPE qtype, channel 83 AGERR_BADRECVMSGRC return code 84 AGERR_CHANNELINFO qtype, msg channel 85 AGERR_ORPHANCHNLCREATED msg channel, qid 86 AGERR_BADQID qtype, qid 87 AGERR_SENDUNLOCKTIMEOUT message, channel 88 AGERR_LESSTHAN10SENDMSG msgs send left 89 AGERR_LESSTHAN10BUFFDESC buff descriptors left 100 AGERR_NOWAITINGBUFFER channel, msgtyp 101 AGERR_USERBUFFERTOOSMALL user buf size, msg bufsiz 211 VBXERR_LOCKSTUCK 212 VBXERR_MSGQFLUSHED 213 VBXERR_INVALID_ADDRESS address Type FF00 - UnixWare, SCO and Solaris Only Error Code Error Name Additional Information 22 AGERR_MSG_BALANCE_LOST with channel, message 42 AGERR_LESS_THAN_48_BYTES with SRAM words left 43 AGERR_RECEIVE_MSG_COUNT with count left, next message SRAM location 44 AGERR_AGMSG_DATA with buffer count, parameter count 81 AGERR_WRITE_QUEUE_EMPTY 100 AGERR_NO_STREAMS_MSG_BLOCK with channel, message 101 AGERR_FLOW_CONTROLLED with channel, message 102 AGERR_CANT_RESPOND_TO_MCTL with command, AGERR_x 421 AGXERR_IDLE_CHANNEL with channel, message 422 AGXERR_BAD_MSG_PARM with pointer to open context, channel 441 AGXERR_BAD_CHANNEL_NUMBER with channel, message 481 AGXERR_CHANNEL_INFO with pointer to open context, channel 482 AGXERR_ORPHAN_CHNL_CREATED with board number, channel 483 AGXERR_BAD_MSG_SIZE with size 484 AGXERR_BAD_MSG with channel, message 485 AGXERR_BAD_MSG_UNIT with unit 486 AGXERR_INVALID_STREAMS_MSG with STREAMS message type 501 AGXERR_FLOW_CONTROLLED with channel, message 603 AGSERR_INVALID_MSGPARMS with parameter count 610 AGSERR_PREVCLOSEFAILED 612 AGSERR_ORPHAN_CHNL_CREATED with channel 613 AGSERR_SERVICE_PRIMITIVE with primitive 614 AGSERR_WRONG_CHANNEL with channel 620 AGSERR_BAD_MSG_UNIT with unit 621 AGSERR_UNEXPECTED_SVC_PRIM with primitive 622 AGSERR_DESTROY_CHNL_FAILED with channel 623 AGSERR_UNEXPECTED_EVENT with event

`value` field, low 16 bits	error code (shown in decimal)
`value` field, high 16 bits	error type (shown in hex)
`size` field, low word	first word of additional data
`size` field, high word	second word of additional data

Error Code	Error Name	Additional Information
-1	NO_SUCH_MSGTYP	Illegal message code
-2	NO_PROCESSORS_BOOTED	On DSP boot, no DSPs booted
-3	SMALL_BUFS_NO_MEM	Not enough system memory for small buffer pool
-4	SMALL_BUFS_NO_CREATE	Creation of small buffer pool failed
-5	LARGE_BUFS_NO_MEM	Not enough system memory for large buffer pool
-6	LARGE_BUFS_NO_CREATE	Creation of large buffer pool failed
-7	NO_MEM_BUF_AVAILABLE	Not enough system memory for allocation request
-8	CANT_FREE_MEM_BUF	Failure to free memory buffer or area
-9	AMX_RSRC_INIT_FAIL	Failure to initialize AMX resource
-10	TPROC_NUM_OUT_OF_RANGE	Task processor number out of range
-11	TPROC_ALREADY_INIT	Task processor already initialized
-12	TPCB_MEM_ALLOC_FAIL	Failure to allocate task proc memory in driver
-13	TLIST_CMEM_ALLOC_FAIL	Failure to allocate task list memory in CMEM
-14	TPROC_WILL_NOT_INIT	Task processor failed to initialize
-15	OCB_MEM_ALLOC_FAIL	Failure to allocate OCB memory in DSP driver
-16	OVLY_DUPLICATE_IDS	Different overlays have same ID
-17	OVLY_ALREADY_LOADED	Overlay is already loaded into driver memory
-18	OVLY_MEM_ALLOC_FAIL	Failure to allocate memory for overlay in driver
-19	CANT_FREE_OVLY_BUF	Failure to free buffer passing overlay
-20	OVLY_NOT_FOUND	Overlay ID not found in OCB list
-21	CANT_FREE_OVLY_BLOCK	Failure to free overlay cleared from driver
-22	OVLY_NOT_IN_DRIVER	Overlay not in driver for downloading to CMEM
-23	OVLY_ALREADY_IN_CMEM	Overlay is already downloaded to CMEM
-24	OVLY_WONT_FIT_IN_CMEM	Failure to allocate overlay space in CMEM
-25	OVLY_NOT_IN_CMEM	Overlay is not currently in CMEM
-26	CANT_FREE_CMEM_OVLY	Failure to free overlay space in CMEM
-27	OVLY_IDCHK_BAD	Overlay ID in CMEM doesn't match that in driver
-28	OVLY_ALREADY_CLEARED	Overlay is already cleared from CMEM
-29	TPROC_NOT_YET_INIT	Task processor not yet initialized
-30	CANT_LOAD_DEFAULT_OVLY	Task processor failed to load default overlay
-31	CANT_FREEZE_CMEM	Failure to freeze CMEM and allocate dynamic blocks
-32	NO_MVIP_CNF_ACTIVE	Neither MVIP config block is active
-33	MVIP_PROCESSOR_ERROR	MVIP processor is reporting an error
-34	TASK_PROCESSOR_ERROR	A task processor is reporting an error
-35	BOOT_EXTRA_BUF_PROBLEM	Can't allocate memory check buffer on DSP booting
-36	BOOT_CMEM_CHECK_ERROR	CMEM memory test failure on DSP booting
-37	SMALL_BUFS_NO_REINIT	Failure to reinitialize small buffer pool
-38	LARGE_BUFS_NO_REINIT	Failure to reinitialize large buffer pool
-39	PORT_ALREADY_OPEN	Port is already open
-40	PORT_IN_USE	Port can't be closed until not in use
-41	STREAM_NOT_AVAILABLE	Selected MVIP stream is not now active
-42	PORTS_IN_USE	Can't select other MVIP stream set when ports open
-43	CHANNEL_ALREADY_OPEN	No more channels available
-44	unused
-45	NO_MEM_FOR_CCB	Failure to allocate memory for CCB
-46	CHANNEL_WAKE_MSG_FAIL	Wakeup message to channel task failed
-47	CHANNEL_NUM_OUT_OF_RANGE	Channel number is out of range
-48	CHANNEL_ALREADY_CLOSED	Channel is already closed
-49	CHANNEL_LIST_NOT_EMPTY	Can't close until all channel lists are empty
-50	CHANNEL_ABORT_MSG_FAIL	Channel abort message failed
-51	CANT_FREE_CCB_MEM	Failure to free CCB memory
-52	FDB_BUFFER_SIZE_ERROR	FDB buffer size and internal size info conflict
-53	FDB_DUPLICATE_IDS	Two FDB's have the same ID
-54	FDB_MEM_ALLOC_FAIL	Failure to allocate memory for the FDB
-55	CANT_FREE_FDB_BUF	Failure to free buffer passing FDB
-56	PORT_NOT_OPEN	Can't assign port until open
-57	SCB_ALLOC_FAIL	Failure to allocate buffer for SCB
-58	PORT_ALREADY_ALLOCATED	Output port is already assigned
-59	INPUT_PORT_INDEX_COLLISION	No other output port assigned for forking
-60	PORT_NOT_IN_USE	Can't release a port not open
-61	PORT_NOT_OWNED_OR_IDLE	Can't release a port either not owned or in use
-62	CANT_FREE_SCB	Failure to free SCB memory buffer
-63	CHANNEL_NOT_OPEN	Request to channel not currently open
-64	INPUT_BUF_ALLOC_FAIL	Can't allocate input buffer for direct connect
-65	STREAM_BUF_ALLOC_FAIL	Can't allocate CMEM stream buf for direct connect
-66	PORT_NOT_CONNECTED	Port is not direct connected
-67	CANT_FREE_STREAM_BUF	Can't free CMEM stream buf on disconnect
-68	CANT_FREE_INPUT_BUF	Can't free input buffer on disconnect
-69	CANT_FREE_OUTPUT_BUF	Can't free output buffer on disconnect
-70	CANT_FIND_PORT_SCB	Port SCB missing on disconnect
-71	CANT_SEND_EVENT	Failure to send event message to channel task
-72	CANT_RELEASE_BUFFER	Failure to free down buffer when empty
-73	CANT_REPORT_BUF_DONE	Failure to report buffer done to channel task
-74	CONTINUATION_BUF_ALLOC_FAIL	Failure to allocate next up buffer when needed
-75	CANT_PASS_BUFFER	Failure to pass up buffer to channel task
-76	OUTPUT_BUF_QUEUE_OVERFLOW	Too many downward buffers submitted
-77	CANT_FIND_FDB	FDB ID not found in list
-78	WRONG_NMBR_PARMS_PASSED	Wrong number parms passed on function start
-79	TVB_ALLOC_FAIL	Failure to allocate task variable block in CMEM
-80	CANT_FREE_PARM_BUFFER	Failure to free buffer passing function parms
-81	CANT_ALLOC_SFCB	Failure to allocate SCB for function
-82	NO_INPUT_PORT_FOR_FUNC	Function needs input port not in LIFO
-83	CANT_ALLOC_STREAM_BUF	Can't allocate stream buffer for func in CMEM
-84	CANT_FREE_SPCB	Can't free SCB buffer used in LIFO
-85	NO_OUTPUT_PORT_FOR_FUNC	Function needs output port not in LIFO
-86	CANT_ALLOC_S3CB	Can't allocate SCB for coprocessor stream
-87	NOT_ENOUGH_BUFFERS_PASSED	Not enough buffers were passed to start function
-88	CANT_ALLOC_INPUT_BUF	Failure to allocate input buf on function start
-89	PASSED_BUFFERS_LEFT_OVER	Buffers were left over on function start
-90	CANT_FREE_PASSED_BUF	Can't free down buf on function stop
-91	CANT_ALLOC_SPCB	Can't allocate SCB for LIFO on function stop
-92	CANT_FREE_SFCB	Can't free function SCB on function stop
-93	CANT_FREE_S3CB	Can't free coprocessor SCB on function stop
-94	FCB_FOR_DIFFERENT_CHANNEL	Channel number in FCB is wrong
-95	CANT_FREE_FCB	Failure to free FCB buffer on function stop
-96	TL_OVLY_NOT_IN_CMEM	Overlay not in CMEM when list building needs it
-97	TL_OVLY_NOT_LOADED	Overlay not in task processor when list build
-98	TL_BUILD_LIST_OVERFLOW	Added list piece overflowed temp build area
-99	TL_OVERLAY_NOT_FOUND	Overlay not in OCB list when needed
-100	TL_OVERLAY_NOT_IN_CMEM	Overlay not in CMEM when needed
-101	TL_PROC_NOT_FOUND	No task processor can run requested function
-102	TL_REM_FUNC_NOT_FOUND	Function to stop doesn't own any list entries
-103	TL_REM_NO_EOL	Function owns past end of task list
-104	TL_REM_BAD_LOAD_FORMAT	Overlay load list format bad
-105	TL_REM_TOO_MANY_SEPS	Bad list structure found
-106	CANT_ALLOC_FCB	Can't allocate FCB buffer on function start
-107	CANT_FIND_FCB	Can't find FCB in list on function stop
-108	COMMAND_STREAM_BUSY	Command already queued when a second is issued
-109	COMMAND_TOO_BIG	More parms passed in command than in cmd stream
-110	NO_COMMAND_STREAM	Command given with no associated active stream
-111	CANT_REPORT_BUF_STARTED	Report of up buffer on function startup failed
-112	INPUT_BUF_QUEUE_OVERFLOW	Too many buf size values passed on func startup
-113	CANT_FREE_TVB_BUF	Can't free TVB in CMEM on function stop
-114	PORT_FOR_IDLE_NOT_FOUND	On change idle command, port not found
-115	OVERFLOW_10MS_STREAMS	Not all 10mS events and bufs in time
-116	DB_PORT_NOT_IDLE	DB port already connected on conn req
-117	DB_NOT_MVIP_CONNECTED	DB port not of MVIP type on disconnect
-118	DB_PORT_NUM_TOO_BIG	DB port num argument passed too big
-119	DB_PORT_NOT_IDLE_CHAN	On discon from chan, slot not idle
-120	DB_PORT_WRONG_CHAN	On disconnect, channel number wrong
-121	DB_PORT_WRONG_INDEX	On disconnect, index doesn't match
-122	DB31_DEMUX_TASK_NOT_DONE	Demux semaphore not set on 10mS period
-123	DB31_MUX_TASK_NOT_DONE	Mux semaphore not set on 10mS period
-124	NO_SPACE_READING_DRV_STRUCT	Buffer too small to get driver struct
-125	WRONG_NUM_OVLYS_ASSIGNED	Too many or no default ovly given TP
-126	LIST_TOO_HIGH_IN_CMEM	TP list allocated into MPROC code area
-127	CMEM_TIMED_OUT
-128	FMIC_ERROR	FMIC or MVIP clock error
-129	UNEXEPECTED_DB_INTERRUPT	DB31 hardware access blocked by DSP
-130	TASK_PROCESSOR_NOT_READY	DSP overloaded or crashed
-131	BAD_EVENT_FORMAT	Mail message from DB31 has bad format
-132	READ_STRUCT_BUF_TOO_SMALL

Error Code	Error Name	Additional Information
-513	BAD_HOST_COMMAND_SEM
-514	BAD_HOST_CMD_BUF_CNT
-515	CANT_GET_HOST_CMD_BUF
-516	CNT_POST_HCMD_TO_SUP
-517	CANT_POST_HCMD_TO_CH
-518	CANT_WAIT_HOST_EVENT
-519	BAD_HOST_EVENT_SEM
-520	CANT_CHANGE_EVENT_PRI
-521	CANT_FREE_EVENT_BUF
-522	CANT_ATTACH_MORE_MGRS
-523	CANT_FIND_MANAGER_ID
-524	MANAGER_NOT_ATTACHED
-525	UNPROCESSED_MESSAGE
-526	CANT_SEND_HOST_MSG
-527	CANT_SEND_MSG_TO_CHAN
-528	HCMD_CHANNEL_NOT_OPEN
-529	CANT_GET_TASK_STACK
-530	CHAN_TASK_CREATE_ERROR
-531	CANT_REPORT_START_CHAN
-532	CANT_SET_CHAN_TERM
-533	NO_CH_TSKS_AVAILABLE
-534	CHAN_ALREADY_STOPPED
-535	CANT_KILL_CHAN_TASK
-536	CANT_DELETE_CHAN_TASK
-537	CANT_SIGNAL_HOST_EVENT
-538	CANT_CREATE_CHAN_TIMER
-539	CANT_DELETE_CHAN_TIMER
-540	CANT_FREE_TASK_STACK
-541	MGR_ALREADY_ATTACHED
-542	CHANNEL_OUT_OF_RANGE
-543	FATAL_FAULT_OR_TRAP	Parms: 1=trap#, 2,3=location, 4-15= eax-edx,esi,edi
-544	AMX_FATAL_EXIT	Parm: AMX fatal exit code.
-545	DEST_CHANNEL_NOT_OPEN
-546	CANT_ALLOC_CONTEXTS	Mem alloc failed
-547	DB31_TOKEN_NOT_GRANTED	db31 hardware access blocked by DSP
-548	DB31_BAD_MAIL_MESSAGE	mail message from DB31 has bad format

Error Code	Error Name	Additional Information
1024	GTPERR_MGR04_NOT_CONFIGURED	START_MANAGER given before CONFIGURE_MGR
1025	GTPERR_BAD_ENGINE_REV	TCP requires different GTP Engine rev
1026	GTPERR_BAD_CHANNEL_NUMBER	Bad channel number
1027	GTPERR_BAD_TCP_NAME	Bad TCP
1028	GTPERR_BAD_BUFFER_COUNT	Bad number of buffers passed
1029	GTPERR_BAD_BUFFER_SIZE	Inconsistent buffer size
1030	GTPERR_BAD_PARAMETER_COUNT	Bad parameter count
1031	GTPERR_BAD_PARAMETER_INDEX	Bad parameter index
1032	GTPERR_PARAM_INIT_ERROR	Cannot init parameter (out of range)
1033	GTPERR_TOO_MANY_TCPS	Too many
1034	GTPERR_CANNOT_ALLOCATE_TCP	Cannot allocate TCP memory
1035	GTPERR_CANNOT_FREE_TCP	Cannot deallocate TCP memory

Error Code	Error Name	Additional Information
1280	TCPERR_BAD_ENGINE_STATE	Incorrect engine state
1281	TCPERR_BAD_ENGINE_OFFSET	Bad engine offset
1282	TCPERR_BAD_STATE_RECORD_ID	Incorrect state record ID
1283	TCPERR_BAD_STATE_NUMBER	Bad state number
1284	TCPERR_BAD_STATE_INDEX	Bad state index
1285	TCPERR_BAD_PARAMETER_COUNT	Bad parameter count
1286	TCPERR_BAD_PARAMETER_INDEX	Bad parameter index
1287	TCPERR_BAD_TCP_INDEX	Bad TCP index
1288	TCPERR_BAD_RECORD_SIZE	Bad record size
1289	TCPERR_BAD_FUNCTION_ORDINAL	Bad service function ordinal
1290	TCPERR_BAD_SERVICE_ARG_LIST	Bad service argument list
1291	TCPERR_BAD_SERVICE_NO_ARGUM	Bad number of service arguments
1292	TCPERR_BAD_ARGUMENT_TYPE	Bad argument type
1293	TCPERR_BAD_TCP_NAME	Bad TCP name
1294	TCPERR_TIMER_CREATION_ERROR	Timer cannot be allocated
1295	TCPERR_TIMER_INDEX_ERROR	Timer index is too large
1296	TCPERR_TOO_MANY_REPLIES	Too many replies used in TCP
1297	TCPERR_TCP_NOT_RUNNING	TCP is has not been started
1298	TCPERR_BAD_STATE_0_FUNC	Bad svc within State#0 initialization
1299	TCPERR_CANNOT_FALL_THROUGH	Bad ON statement to fall through
1300	TCPERR_GTP_COMMAND_IGNORED	Unexpected command to GTP
1301	TCPERR_BAD_FUNC_IN_TRGREC	Bad svc within trigger record
1302	TCPERR_BAD_FUNC_IN_STATE	Bad svc within state initialization
1303	TCPERR_BAD_FUNC_IN_SUBR	Bad svc within subroutine initialization
1304	TCPERR_INVALID_TRGREC_ID	Invalid trigger record ID
1321	TCPERR_INVALID_REC_ID_SIZE	Invalid record id_size
1322	TCPERR_SUBR_ON_NOT_FOUND	Subroutine ON statement not found
1323	TCPERR_BAD_SERVICE_RETURN	SVC mgr returned an error code
1324	TCPERR_INVALID_TOKEN_INDEX	Request to access token out of range
1325	TCPERR_ILLEGAL_BRANCH	Request to branch out of range
1328	TCPERR_CANNOT_ALLOC_MEM	Cannot allocate AMX memory
1329	TCPERR_FUNC_CANNOT_RESTART	Cannot start an already running func
1330	TCPERR_FUNC_NOT_STARTED	Cannot stop a not running function
1331	TCPERR_BAD_SVC_ARG_VALUE	Incorrect argument value in svc routine
1332	TCPERR_BAD_BUFFER_COUNT	Bad buffer count
1342	TCPERR_BAD_SVC_RETURN	Service routine returned a bad code
1343	TCPERR_CANNOT_REPLY_ASYNC	Cannot use REPLY on ASYNC events

Error Code	Error Name
-1024	FMICERR_LIBRARY_NOT_USABLE
-1025	FMICERR_LIBRARY_INITIALIZED
-1026	FMICERR_LOCK_CREATION_FAILED
-1027	FMICERR_LOCK_FAILED
-1028	FMICERR_UNLOCK_FAILED
-1029	FMICERR_DELAY_FAILED
-1030	FMICERR_INTERNAL_MACRO
-1031	FMICERR_CONNECT_REFERENCE_CNT
-1032	FMICERR_INVALID_LOCAL_DEVICE
-1033	FMICERR_INVALID_STREAM
-1034	FMICERR_INVALID_TIMESLOT
-1035	FMICERR_INVALID_CLOCK_PARM
-1036	FMICERR_INVALID_MODE
-1037	FMICERR_INVALID_PARAMETER
-1038	FMICERR_NO_PATH
-1039	FMICERR_SWITCH_VERIFY_FAILED
-1040	FMICERR_CONNECT_NOT_SUPPORTED
-1041	FMICERR_MODE_NOT_SUPPORTED

Error Code	Error Name	Additional Information
1	AGV_ERROR_UNSUPPORTED_CMD	cmd, 0
2	AGV_ERROR_UNSUPPORTED_MODE	command, data
3	AGV_ERROR_COMMAND_NOT_IMPL	command
4	AGV_ERROR_WRONG_BUF_COUNT	command, bcnt
5	AGV_ERROR_WRONG_PARM_COUNT	command, pcnt
6	AGV_ERROR_UNEXPECTED_CMD	command, cur function
7	AGV_ERROR_UNEXPECTED_EVENT	msgtyp, parm0
8	AGV_ERROR_ACTIVE_FUNCTION	command, state
9	AGV_ERROR_DRVAPI_ERROR	DSP err, cmd
10	AGV_ERROR_SVC_ERROR	SVC err, cmd
11	AGV_ERROR_TIMER_FAIL	return code, 0/1/2
12	AGV_ERROR_EVENT4WRONGFUNC	msg function, cur state
13	AGV_ERROR_UNEXPECTED_BUFF	state
14	AGV_ERROR_BUFFER_OVERRUN	buf count
15	AGV_ERROR_WRONG_BUFFER_DIR
16	AGV_ERROR_INTERNAL_ERROR	error number
17	AGV_ERROR_MEMALLOC	cmd, error code
18	AGV_ERROR_MGR_NOT_INIT	cmd, 0
19	AGV_ERROR_INVALID_PARM	cmd, parmval
20	AGV_ERROR_DSP_SERVICE	cmd, errval
21	AGV_ERROR_DIGTIMING_ACTIVE	cmd, 0
22	AGV_ERROR_FUNC_NOT_AVAIL	cmd, 0

Error Code	Error Name	Additional Information
4353	SVCERR_INVALID_ARG	Invalid arg value passed
4354	SVCERR_NUM_OF_ARGS	Invalid number of args
4355	SVCERR_FUNC_NOT_STARTED	Can't modify inactive func
4356	SVCERR_CANNOT_RESTART	Can't restart active func
4357	SVCERR_TIMER_CREATE_ERROR	Error creating timers
4358	SVCERR_TIMER_ERROR	Error using timing services
4359	SVCERR_MEMORY_ALLOC	Error doing mem alloc
4360	SVCERR_ACCESS_DENIED	Function is locked
4361	SVCERR_FUNC_NOT_AVAILABLE	Function not loaded/avail
4362	SVCERR_DRV_API_RESOURCE	Func failed,missed resource
4386	SVCERR_DRV_API_ERROR	DSP driver error.

Error Code	Error Name	Additional Information
1	AGERR_LOCKFAILED
21	AGERR_IDLECHANNEL	channel, msgtyp
22	AGERR_MSGBALANCELOST	channel, msgtyp
42	AGERR_LESSTHAN48BYTES	SRAM words left
43	AGERR_RECVMSGCOUNT	count left, next loc
44	AGERR_SRAM_STATE	state
45	AGERR_BADCHANNEL	channel, msgtyp
46	AGERR_MSGSNOTSENT	qid, count left
47	AGERR_BADMGHDR
81	AGERR_SENDQEMPTY
82	AGERR_BADQTYPE	qtype, channel
83	AGERR_BADRECVMSGRC	return code
84	AGERR_CHANNELINFO	qtype, msg channel
85	AGERR_ORPHANCHNLCREATED	msg channel, qid
86	AGERR_BADQID	qtype, qid
87	AGERR_SENDUNLOCKTIMEOUT	message, channel
88	AGERR_LESSTHAN10SENDMSG	msgs send left
89	AGERR_LESSTHAN10BUFFDESC	buff descriptors left
100	AGERR_NOWAITINGBUFFER	channel, msgtyp
101	AGERR_USERBUFFERTOOSMALL	user buf size, msg bufsiz
211	VBXERR_LOCKSTUCK
212	VBXERR_MSGQFLUSHED
213	VBXERR_INVALID_ADDRESS	address

Error Code	Error Name	Additional Information
22	AGERR_MSG_BALANCE_LOST	with channel, message
42	AGERR_LESS_THAN_48_BYTES	with SRAM words left
43	AGERR_RECEIVE_MSG_COUNT	with count left, next message SRAM location
44	AGERR_AGMSG_DATA	with buffer count, parameter count
81	AGERR_WRITE_QUEUE_EMPTY
100	AGERR_NO_STREAMS_MSG_BLOCK	with channel, message
101	AGERR_FLOW_CONTROLLED	with channel, message
102	AGERR_CANT_RESPOND_TO_MCTL	with command, AGERR_x
421	AGXERR_IDLE_CHANNEL	with channel, message
422	AGXERR_BAD_MSG_PARM	with pointer to open context, channel
441	AGXERR_BAD_CHANNEL_NUMBER	with channel, message
481	AGXERR_CHANNEL_INFO	with pointer to open context, channel
482	AGXERR_ORPHAN_CHNL_CREATED	with board number, channel
483	AGXERR_BAD_MSG_SIZE	with size
484	AGXERR_BAD_MSG	with channel, message
485	AGXERR_BAD_MSG_UNIT	with unit
486	AGXERR_INVALID_STREAMS_MSG	with STREAMS message type
501	AGXERR_FLOW_CONTROLLED	with channel, message
603	AGSERR_INVALID_MSGPARMS	with parameter count
610	AGSERR_PREVCLOSEFAILED
612	AGSERR_ORPHAN_CHNL_CREATED	with channel
613	AGSERR_SERVICE_PRIMITIVE	with primitive
614	AGSERR_WRONG_CHANNEL	with channel
620	AGSERR_BAD_MSG_UNIT	with unit
621	AGSERR_UNEXPECTED_SVC_PRIM	with primitive
622	AGSERR_DESTROY_CHNL_FAILED	with channel
623	AGSERR_UNEXPECTED_EVENT	with event

(Page 2 of 2 in this chapter)

Tech_Support@nmss.com