On the S Connect: MVIP-90 Commands	MVIP-95 Commands
`UnMakeConnection(16:4 to 0:4)` `UnMakeConnection(0:4 to 16:4)` `MakeConnection(16:4 to 14:5)` `MakeConnection(14:5 to 16:4)`	`UnMakeConnection(LOCAL:0:4 to MVIP:1:4)` `UnMakeConnection(MVIP:0:4 to LOCAL:1:4)` `MakeConnection(LOCAL:0:4 to MVIP:12:5)` `MakeConnection(MVIP:13:5 to LOCAL:1:4)`

On the S Connect: MVIP-90 Commands	MVIP-95 Commands
`UnMakeConnection(16:4 to 14:5)` `UnMakeConnection(14:5 to 16:4)` `MakeConnection(16:4 to 0:4)` `MakeConnection(0:4 to 16:4)`	`UnMakeConnection(LOCAL:0:4 to MVIP:12:5)` `UnMakeConnection(MVIP:13:5 to LOCAL:1:4)` `MakeConnection(LOCAL:0:0 to MVIP:1:4)` `MakeConnection(MVIP:0:4 to LOCAL:1:4)`

(Page 1 of 1 in this chapter)

Appendix B

Switching Examples

Introduction

This appendix shows the switching commands for a typical switching application. The boards in the system are: Board Functionality AG-T1 24 T1 channels with 24 ports of DSP resources S Connect-24 24 operator workstation interfaces AG-24 24 ports of DSP resources used for DTMF/tone generation and detection for the S Connect-24

Board	Functionality
AG-T1	24 T1 channels with 24 ports of DSP resources
S Connect-24	24 operator workstation interfaces
AG-24	24 ports of DSP resources used for DTMF/tone generation and detection for the S Connect-24

Switching Example

The following default switch connections are made: Board Default Connections AG-T1 Switch connections to connect the network interface voice and signaling streams to the on-board DSP resources. S Connect-24 Switch connections to connect the operator workstation voice and signaling streams to the AG-24 DSP resources. AG-24 MVIP-90: Voice data nailed up to stream 0; signaling data nailed up to stream 1. MVIP-95: Voice data nailed up to streams 0 and 1; signaling data nailed up to streams 2 and 3. .
The following steps show how a typical incoming call is switched: A call is received on the first T1 channel. A voice prompt is played using the on-board DSP resources. The caller is instructed to enter a digit for the service he requires. The on-board DSP resources are used to detect the entered digit. The caller presses "5" to speak to an operator. The caller is connected to an available operator workstation (on timeslot 4) on the S Connect board using MVIP streams 12 and 13: The voice on the AG-T1 channel is disconnected from the on-board DSP resources. The voice on the fifth operator workstation is disconnected from the AG-24 DSP resources. The voice on the T1 channel and the voice on the operator workstation are connected using the MVIP bus. On the AG-T1: MVIP-90 Commands MVIP-95 Commands UnMakeConnection(16:0 to 17:0) UnMakeConnection(17:0 to 16:0) MakeConnection(16:0 to 6:5) MakeConnection(6:5 to 16:0) UnMakeConnection(LOCAL:0:0 to LOCAL:5:0) UnMakeConnection(LOCAL:4:0 to LOCAL:1:0) MakeConnection(LOCAL:0:0 to MVIP:13:5) MakeConnection(MVIP:12:5 to LOCAL:1:0) On the S Connect: MVIP-90 Commands MVIP-95 Commands UnMakeConnection(16:4 to 0:4) UnMakeConnection(0:4 to 16:4) MakeConnection(16:4 to 14:5) MakeConnection(14:5 to 16:4) UnMakeConnection(LOCAL:0:4 to MVIP:1:4) UnMakeConnection(MVIP:0:4 to LOCAL:1:4) MakeConnection(LOCAL:0:4 to MVIP:12:5) MakeConnection(MVIP:13:5 to LOCAL:1:4) When the call is complete, the AG-T1 and the S-Connect channels are disconnected from the MVIP bus, and re-connected to DSP resources. On the AG-T1: MVIP-90 Commands MVIP-95 Commands UnMakeConnection(16:0 to 6:5) UnMakeConnection(6:5 to 16:0) MakeConnection(16:0 to 17:0) MakeConnection(17:0 to 16:0) UnMakeConnection(LOCAL:0:0 to MVIP:13:5) UnMakeConnection(MVIP:12:5 to LOCAL:1:0) MakeConnection(LOCAL:0:0 to LOCAL:5:0) MakeConnection(LOCAL:4:0 to LOCAL:1:0) On the S Connect: MVIP-90 Commands MVIP-95 Commands UnMakeConnection(16:4 to 14:5) UnMakeConnection(14:5 to 16:4) MakeConnection(16:4 to 0:4) MakeConnection(0:4 to 16:4) UnMakeConnection(LOCAL:0:4 to MVIP:12:5) UnMakeConnection(MVIP:13:5 to LOCAL:1:4) MakeConnection(LOCAL:0:0 to MVIP:1:4) MakeConnection(MVIP:0:4 to LOCAL:1:4)

Board	Default Connections
AG-T1	Switch connections to connect the network interface voice and signaling streams to the on-board DSP resources.
S Connect-24	Switch connections to connect the operator workstation voice and signaling streams to the AG-24 DSP resources.
AG-24	MVIP-90: Voice data nailed up to stream 0; signaling data nailed up to stream 1. MVIP-95: Voice data nailed up to streams 0 and 1; signaling data nailed up to streams 2 and 3.

On the AG-T1: MVIP-90 Commands	MVIP-95 Commands
`UnMakeConnection(16:0 to 17:0)` `UnMakeConnection(17:0 to 16:0)` `MakeConnection(16:0 to 6:5)` `MakeConnection(6:5 to 16:0)`	`UnMakeConnection(LOCAL:0:0 to LOCAL:5:0)` `UnMakeConnection(LOCAL:4:0 to LOCAL:1:0)` `MakeConnection(LOCAL:0:0 to MVIP:13:5)` `MakeConnection(MVIP:12:5 to LOCAL:1:0)`

On the AG-T1: MVIP-90 Commands	MVIP-95 Commands
`UnMakeConnection(16:0 to 6:5)` `UnMakeConnection(6:5 to 16:0)` `MakeConnection(16:0 to 17:0)` `MakeConnection(17:0 to 16:0)`	`UnMakeConnection(LOCAL:0:0 to MVIP:13:5)` `UnMakeConnection(MVIP:12:5 to LOCAL:1:0)` `MakeConnection(LOCAL:0:0 to LOCAL:5:0)` `MakeConnection(LOCAL:4:0 to LOCAL:1:0)`

(Page 1 of 1 in this chapter)

tech_support@nmss.com