(Page 3 of 4 in this chapter)

Alphabetical Error Summary

The following table is an alphabetical listing of Switching service errors. All errors are 32 bits.

Error Name

Hex

Decimal

Description

SWIERR_CONNECTION_NOT_SUPPORTED

0x40011

262161

The switch block does not support the requested connection. There is a permanent limitation in the switch block that prevents the connection.

SWIERR_DEVICE_ERROR

0x40002

262146

The MVIP device driver encountered an error while using the services of another device driver.

SWIERR_DLL_INVALID_DEVICE

0x40001

262145

The Dynamic Link Library (DLL) could not find the requested device.

SWIERR_INTERNAL_CONFLICT

0x40010

262160

A switch component of a switch matrix conflicts with another switch component (the state of the switch matrix is ambiguous).

SWIERR_INVALID_CLOCK_PARM

0x40007

262151

Problem: The value of a clock configuration parameter is invalid.
Solution: Enter a valid value.

SWIERR_INVALID_COMMAND

0x40000

262144

The device driver does not support the requested operation.

SWIERR_INVALID_MINOR_SWITCH

0x4000B

262155

The value of the switch parameter is invalid.

SWIERR_INVALID_MODE

0x4000A

262154

Problem: The device driver does not support the setting of the mode of an output terminus to the mode specified (e.g., swiMakeFramedConnection is not supported in all hardware or by MVIP-90 drivers).
Solution: Enter a valid mode.

SWIERR_INVALID_PARAMETER

0x4000C

262156

Problem: The parameter needed by the called function is set to an invalid value.
Solution: Enter a valid value.

SWIERR_INVALID_SPEED

0x40008

262152

Problem: An invalid stream speed capacity was entered.
Solution: This functionality only works in MVIP-95. Enter one of the following acceptable speed values:
MVIP95_2MBPS_STREAM_SPEED MVIP95_4MBPS_STREAM_SPEED MVIP95_8MBPS_STREAM_SPEED

SWIERR_INVALID_STREAM

0x40004

262148

Problem: The value of stream in a terminus element is out of range.
Solution: Enter a valid value for stream in the terminus element.

SWIERR_INVALID_TIMESLOT

0x40005

262149

Problem: The value of timeslot in a terminus element is out of range.
Solution: Enter a valid value for timeslot in the terminus element.

SWIERR_MISSING_PARAMETER

0x40006

262150

An insufficient number of parameters were provided for the driver to complete the command.

SWIERR_MVIP_BUS_NOT_ENABLED

0x40012

262162

Problem: A switching command was called on a switch block on which the MVIP bus was not enabled.
Solution: Enable MVIP in the ag.cfg file for the switch block.

SWIERR_NO_PATH

0x4000E

262158

The device driver is unable to complete the connection because there is blocking or some other temporary switch limitation encountered.

SWIERR_NOT_CONFIGURABLE

0x40009

262153

The device does not support configuration of the parameters and/or values requested.

SWIERR_SWITCH_VERIFY_ERROR

0x4000F

262159

Verification of the switch operation failed.

SWIERR_UNSUPPORTED_MODE

0x4000D

262157

The mode is not supported by either the device driver or the hardware below the driver.

Error Name	Hex	Decimal	Description
`SWIERR_CONNECTION_NOT_SUPPORTED`	`0x40011`	`262161`	The switch block does not support the requested connection. There is a permanent limitation in the switch block that prevents the connection.
`SWIERR_DEVICE_ERROR`	`0x40002`	`262146`	The MVIP device driver encountered an error while using the services of another device driver.
`SWIERR_DLL_INVALID_DEVICE`	`0x40001`	`262145`	The Dynamic Link Library (DLL) could not find the requested device.
`SWIERR_INTERNAL_CONFLICT`	`0x40010`	`262160`	A switch component of a switch matrix conflicts with another switch component (the state of the switch matrix is ambiguous).
`SWIERR_INVALID_CLOCK_PARM`	`0x40007`	`262151`	Problem: The value of a clock configuration parameter is invalid. Solution: Enter a valid value.
`SWIERR_INVALID_COMMAND`	`0x40000`	`262144`	The device driver does not support the requested operation.
`SWIERR_INVALID_MINOR_SWITCH`	`0x4000B`	`262155`	The value of the switch parameter is invalid.
`SWIERR_INVALID_MODE`	`0x4000A`	`262154`	Problem: The device driver does not support the setting of the mode of an output terminus to the mode specified (e.g., swiMakeFramedConnection is not supported in all hardware or by MVIP-90 drivers). Solution: Enter a valid mode.
`SWIERR_INVALID_PARAMETER`	`0x4000C`	`262156`	Problem: The parameter needed by the called function is set to an invalid value. Solution: Enter a valid value.
`SWIERR_INVALID_SPEED`	`0x40008`	`262152`	Problem: An invalid stream speed capacity was entered. Solution: This functionality only works in MVIP-95. Enter one of the following acceptable speed values: `MVIP95_2MBPS_STREAM_SPEED MVIP95_4MBPS_STREAM_SPEED MVIP95_8MBPS_STREAM_SPEED`
`SWIERR_INVALID_STREAM`	`0x40004`	`262148`	Problem: The value of stream in a terminus element is out of range. Solution: Enter a valid value for stream in the terminus element.
`SWIERR_INVALID_TIMESLOT`	`0x40005`	`262149`	Problem: The value of timeslot in a terminus element is out of range. Solution: Enter a valid value for timeslot in the terminus element.
`SWIERR_MISSING_PARAMETER`	`0x40006`	`262150`	An insufficient number of parameters were provided for the driver to complete the command.
`SWIERR_MVIP_BUS_NOT_ENABLED`	`0x40012`	`262162`	Problem: A switching command was called on a switch block on which the MVIP bus was not enabled. Solution: Enable MVIP in the `ag.cfg` file for the switch block.
`SWIERR_NO_PATH`	`0x4000E`	`262158`	The device driver is unable to complete the connection because there is blocking or some other temporary switch limitation encountered.
`SWIERR_NOT_CONFIGURABLE`	`0x40009`	`262153`	The device does not support configuration of the parameters and/or values requested.
`SWIERR_SWITCH_VERIFY_ERROR`	`0x4000F`	`262159`	Verification of the switch operation failed.
`SWIERR_UNSUPPORTED_MODE`	`0x4000D`	`262157`	The mode is not supported by either the device driver or the hardware below the driver.

(Page 3 of 4 in this chapter)

tech_support@nmss.com