- The following PPX configuration file includes a variety of NMS boards.
ppx.cfg
#
# --- Point-to-Point Switching Service ---
# --- Configuration ---
#
# This file defines to the Point-to-Point Switching service
# the available bus, timeslots, and switches it may use for
# establishing connection paths.
#
# This configuration file contains example switch definitions
# for the various NMS boards. Use this as a guide for
# configuring the PPX service to your particular hardware
# configuration.
#
# Some Reminders:
# - All switch numbers must be unique.
# - The "DeviceNumber" is the board number established
# during H/W configuration, e.g., in "ag.cfg"
# - The PPX service uses MVIP-95, not MVIP-90.
#
#
[PPX]
Fabric
Bus H100 # H100 bus
CTBUS:0..15:0..31
CTBUS:16..23:0..63
CTBUS:24..31:0..127
End Bus
Bus MVIP_90 # MVIP-90 bus
Bus H100 (CTBUS:0..15:0..31)
End Bus
Switch 0 # AG-8
SwitchType = FMIC
DeviceName = "agsw"
DeviceNumber = 0
Bus H100 (CTBUS:0..15:0..31) # on the MVIP-90 bus
Inputs
LOCAL:0..6(2):0..7 # line interfaces & DSP resources
End Inputs
Outputs
LOCAL:1..7(2):0..7 # line interfaces & DSP resources
End Outputs
End Switch
Switch 1 # AG-T1
SwitchType = FMIC
DeviceName = "agsw"
DeviceNumber = 3
Bus MVIP_90 () # on the MVIP-90 bus
Inputs
LOCAL:0..6(2):0..23 # line interfaces & DSP resources
End Inputs
Outputs
LOCAL:1..7(2):0..23 # line interfaces & DSP resources
End Outputs
End Switch
Switch 2 # AG Quad T
SwitchType = HMIC
DeviceName = "agsw"
DeviceNumber = 2
Bus H100 ()
Inputs
LOCAL:0..14(2):0..23 # Trunk
LOCAL:16..18(2):0..127 # DSP
End Inputs
Outputs
LOCAL:1..15(2):0..23 # Trunk
LOCAL:17..19(2):0..127 # DSP
End Outputs
End Switch
Switch 4 # AG Dual T
SwitchType = HMIC
DeviceName = "agsw"
DeviceNumber = 4
Bus H100 ()
Inputs
LOCAL:0..14(2):0..23 # Trunk
LOCAL:16..18(2):0..127 # DSP
End Inputs
Outputs
LOCAL:1..15(2):0..23 # Trunk
LOCAL:17..19(2):0..127 # DSP
End Outputs
End Switch
Switch 5 # Quad Connect T
SwitchType = HMIC
DeviceName = "agsw"
DeviceNumber = 5
Bus H100 ()
Inputs
LOCAL:0..14(2):0..23 # Trunk
End Inputs
Outputs
LOCAL:1..15(2):0..23 # Trunk
End Outputs
End Switch
#
# AG-24 Resource Board (no physical switch)
#
# Note: In this example, the ag.cfg file contains the following
# definition of stream usage for the AG Resouce board.
#
# MVIPSlot = 4:0..23
# MVIPSlot = 5:0..23 # signaling
#
# But, the ag.cfg file uses the MVIP-90 standard for
# stream numbering; using MVIP-95, this translates into:
#
# MVIP-90 stream 4 is MVIP-95 streams 8 and 9
# MVIP-90 stream 5 is MVIP-95 streams 10 and 11
#
Switch 6 # AG-24 "virtual switch"
Inputs
Bus MVIP_90 (CTBUS:9..11(2):0..23)
End Inputs
Outputs
Bus MVIP_90 (CTBUS:8..10(2):0..23)
End Outputs
End Switch
Switch 7 # AG-30
Inputs
Bus MVIP_90 (CTBUS:4..6(2):0..29) # Connections nailed up
End Inputs
Outputs
Bus MVIP_90 (CTBUS:5..7(2):0..29)
End Outputs
End Switch
Switch 8 # assigned as switch 1
DeviceName = "mc1sw" # MC1 board switch driver - mc1sw
DeviceNumber = 0 # the number assigned during install.
SwitchType = FMIC # the switch on the MC1 is an FMIC
Bus MVIP_90 () # MC1 is connected to the MVIP-90 bus
Inputs
MC1:0..42(2):0..63 # 22 input streams
End Inputs
Outputs
MC1:1..7(2):0..63 # 4 output streams (1, 3, 5, 7)
End Outputs
End Switch
Switch 9 # WTI-8
SwitchType = FMIC
DeviceName = "wti8sw"
DeviceNumber = 0
Bus MVIP_90 () # on the MVIP-90 bus
Inputs
LOCAL:0..2(2):0..7 # 8 line interfaces
End Inputs
Outputs
LOCAL:1..3(2):0..7 # 8 line interfaces
End Outputs
End Switch
Switch 10 # T Connect-24
SwitchType = FMIC
DeviceName = "agcxsw"
DeviceNumber = 0
Bus MVIP_90 () # on the MVIP-90 bus
Inputs
LOCAL:0..2(2):0..23 # 24 line interfaces
End Inputs
Outputs
LOCAL:1..3(2):0..23 # 24 line interfaces
End Outputs
End Switch
Switch 11 # S Connect-12
SwitchType = FMIC
DeviceName = "agcxsw"
DeviceNumber = 1
Bus MVIP_90 () # on the MVIP-90 bus
Inputs
LOCAL:0..2(2):0..11 # 12 station interfaces
End Inputs
Outputs
LOCAL:1..3(2):0..11 # 12 station interfaces
End Outputs
End Switch
Switch 12 # ATI
SwitchType = ATI
DeviceName = "atsdrv"
DeviceNumber = 0
Bus H100 (CTBUS:0..15:0..31)
Inputs
LOCAL:0..2(2):0..23 # 24 Analog loop start lines; no DSPs
End Inputs
Outputs
LOCAL:1..3(2):0..23
End Outputs
End Switch
Switch 13 # AG2000
SwitchType = HMIC
DeviceName = "agsw"
DeviceNumber = 0
Bus H100 ()
Inputs
LOCAL:0..2(2):0..7 # Trunk
LOCAL:4..6(2):0..7 # DSP
End Inputs
Outputs
LOCAL:1..3(2):0..7 # Trunk
LOCAL:5..7(2):0..7 # DSP
End Outputs
End Switch
Switch 14 # AG4000
SwitchType = HMIC
DeviceName = "agsw"
DeviceNumber = 1
Bus H100 ()
Inputs
LOCAL:0..14(2):0..23 # Trunk (or ..29 for Es)
LOCAL:16..18(2):0..127 # DSP
End Inputs
Outputs
LOCAL:1..15(2):0..23 # Trunk (or ..29 for Es)
LOCAL:17..19(2):0..127 # DSP
End Outputs
End Switch
Switch 15 # CompactPCI Quad
SwitchType = HMIC
DeviceName = "agsw"
DeviceNumber = 1
Bus H100 ()
Inputs
LOCAL:0..14(2):0..23 # Trunk (or ..29 for Es)
LOCAL:16..18(2):0..127 # DSP
End Inputs
Outputs
LOCAL:1..15(2):0..23 # Trunk (or ..29 for Es)
LOCAL:17..19(2):0..127 # DSP
End Outputs
End Switch
Switch 16 # QX 2000/80-4L
SwitchType = FMIC
DeviceName = "qxsw"
DeviceNumber = 1
Bus MVIP_90 ()
Inputs
LOCAL:0..2(2):0..3 # Trunk
LOCAL:4..6(2):0..3 # DSP
End Inputs
Outputs
LOCAL:1..3(2):0..3 # Trunk
LOCAL:5..7(2):0..3 # DSP
End Outputs
End Switch
Switch 17 # QX 2000/100-4L
SwitchType = HMIC
DeviceName = "qxsw"
DeviceNumber = 1
Bus H100 ()
Inputs
LOCAL:0..2(2):0..3 # Trunk
LOCAL:4..6(2):0..3 # DSP
End Inputs
Outputs
LOCAL:1..3(2):0..3 # Trunk
LOCAL:5..7(2):0..3 # DSP
End Outputs
End Switch
Connect
0:local:0:0 to 0:local:5:0 QUAD
0:local:0:2 to 0:local:5:2 QUAD NAILED
End Connect
End Fabric
(Page 1 of 1 in this chapter)