(Page 1 of 1 in this chapter)


Appendix D

Hardware Specifications


Host Interface

Electrical

PC-AT bus designed to IEEE P996 ISA

Mechanical

Designed to IBM's specification, as described in IBM's Personal Computer Hardware Reference Library publication 6361674, Prototype Adapter

Bus Speed

4-8 MHz

I/O Base Address

Selectable to any of 16 I/O addresses

External Power Supply

Output

· -24V DC, 1A minimum current

· Boards With Ringing: 93V AC, 120mA (with -24V DC) minimum

Regulation

+/- 1 Volt

Ripple

5 mV rms maximum

Recommended Model

CNB power supply (NMS P/N 31468)

Power Requirements

Supply Voltage

Current

+5 DC

1.25 A

+12 DC

160 mA

-12 DC

450 mA

Note: These figures correspond to an S Connect 24 port interface board

Environment

Operating Temp

0 - 50 deg C

Storage Temp

-20 to 70 deg C

Humidity

5% to 80%, non-condensing


 
MVIP Compliant Interface

· Switchable access to any of 512 MVIP timeslots

· MVIP clock master or clock slave (software selectable)

· Able to terminate the MVIP bus (jumper selectable)

· Compatible with any MVIP compliant telephony interface

OWS Interface

Crosstalk

-80 dB maximum (0dB, 300 to 400 Hz)

Connector

A high density 62 pin female D-subminiature connector. The adapter cable, with a 62 pin male connector on one end and a male RJ21X on the other, provides for direct connection to OWS phones and to a power supply.

LEDs

· Two yellow LEDs on the end bracket indicate whether the AC and DC voltage are connected correctly. For details, see Chapter 4.

· A green LED on the face of the board indicates whether the board is operating correctly. For details, see Chapter 4.

· A red LED on the face of the board lights whenever the OWS phone on line interface 1 rings. For details, see Chapter 4.

Bus Connectors

PC-AT Bus

Pin-outs and signals of the PC-AT bus follow IEEE P996 ISA specifications.

MVIP Bus

The MVIP bus connector is a shrouded 40-pin 3M 2540-50020B, positioned as specified in Section 3 of the MVIP-90 Standard, Release 1.1 manual. Pin-outs and signals of the MVIP bus follow the specifications given in the manual.

Telephone Interface

The following tables list the signals and pin numbers from the AG Connect board to the local OWS telephone sets and power supply:
Channel

Signal Name

DB 62

Connector Pin No.

Male RJ21X Pin No.

1

R

44

1

T

43

26

2

R

23

2

T

22

27

3

R

2

3

T

1

28

4

R

3

4

T

24

29

5

R

4

5

T

25

30

6

R

46

6

T

45

31

7

R

5

7

T

26

32

8

R

6

8

T

27

33

9

R

7

9

T

28

34

10

R

49

10

T

48

35

11

R

8

11

T

29

36

12

R

9

12

T

30

37

13

R

10

13

T

31

38

14

R

52

14

T

51

39

15

R

11

15

T

32

40

16

R

12

16

T

33

41

17

R

13

17

T

34

42

18

R

55

18

T

54

43

19

R

14

19

T

35

44

20

R

15

20

T

36

45

21

R

16

21

T

37

46

22

R

50

22

T

57

47

23

R

17

23

T

38

48

24

R

18

24

T

39

49

.
Power Supply Connections

Signal Name

DB 62 Connector Pin No.

AMP Connector Pin No.

Ext. BAT (-24V DC)

20, 41

1

Ext. BAT COMMON

21, 42

4

AC COMMON

61

3

AC RING (93V AC)

62

2

Conferencing Limits

Up to 16 seats may be distributed among up to 5 conferences. NMS recommends a maximum of 8 seats per conference.



(Page 1 of 1 in this chapter)


tech_support@nmss.com
Copyright © 1999, Natural MicroSystems, Inc. All rights reserved.