AG 4000C Installation and Developer's Manual

P/N 6589-12
Version

(Page 1 of 1 in this chapter)

Table of Contents

About This Manual

Developer Support

1 Overview of the AG 4000C Board

1.1 Introduction
1.2 AG 4000C Board Features
1.3 Software Components
1.3.1 Application Programming Interface
1.3.2 Runtime Software
1.3.3 Trunk Control Programs (TCPs)
1.3.4 AG Configuration File and agmon
1.4 Compatibility With Telephony Standards

2 Installing the Hardware

2.1 Introduction
2.2 Installation Summary
2.3 System Requirements
2.4 DIP Switches
2.5 Installing the Hardware
2.5.1 Installing the AG 4000C Board
2.5.2 Keying Information
2.6 Connecting to the T1 or E1 Trunk
2.7 Connecting an AG 4000C T Board to the Network
2.7.1 Ordering T1 Service
2.8 Connecting an AG 4000C E Board to the Network
2.8.1 Connecting an AG 4000C E 120 ohm
2.8.2 Connecting an AG 4000C E 75 ohm
2.9 Loopback Configuration

3 Editing the AG Configuration File

3.1 Introduction
3.2 AG Configuration File Summary
3.3 Creating an AG Configuration File
3.3.1 Assigning an AG 4000C Board Number
3.3.2 Determining CompactPCI Bus and Slot Location
3.3.3 Interrupts
3.3.4 Trunk-Specific Settings
3.3.5 DSP Files
3.3.6 Configuring a Standalone AG 4000C Board
3.3.7 Enabling Telephony Bus Switching
3.3.8 Telephony Bus Clocking
3.3.9 Echo Cancellation
3.4 Running agmon
3.5 Sample AG Configuration File

4 Verifying the Installation

4.1 Introduction
4.2 Status Indicator LEDs
4.3 Verifying That the Board is Installed Correctly
4.4 Verifying That the Board is Working Correctly
4.5 Demonstration Programs

5 T1 and E1 Trunk Channels

5.1 Introduction
5.2 Channels and Transmission Rates
5.3 Signaling
5.3.1 Channel Associated Signaling (CAS)
5.3.2 Common Channel Signaling (CCS)
5.4 Framing
5.4.1 T1 Framing
5.4.2 E1 Framing
5.5 Voice Encoding
5.5.1 Companding
5.6 AMI, Ones Density, and Zero Code Suppression

6 AG 4000C Switching

6.1 Introduction
6.2 AG 4000C Switch Model
6.2.1 Lucent T8100A Switch Blocking
6.3 T1 Trunk Channels and H.110 Timeslots
6.3.1 T1 Channels/Timeslots for Channel Associated Signaling
6.3.2 T1 Channels/Timeslots for Common Channel Signaling
6.3.3 T1 Channels and Timeslots for RAW Mode
6.4 E1 Trunk Channels and Timeslots
6.4.1 E1 Signaling for Channel Associated Signaling
6.4.2 E1 Signaling/Timeslots for Common Channel Signaling
6.4.3 E1 Channels and Timeslots for RAW Mode
6.5 Default Connections for Standalone Board
6.6 Using CT Access Switch Commands
6.6.1 Configuring Framer Parameters
6.6.2 Configuring Channel Parameters
6.6.3 Retrieving Local Device Information

Appendix A Glossary

Appendix B Hardware Specifications

General
Protocols
Host Interface
H.110 Compliant Interface
Environment
Power Requirements for AG 4000C/1600
Power Requirements for AG 4000C/3200
Power Requirements for AG 4000C/4800
CEPT E1 G.703 Telephony Interface
DSX-1 Telephony Interface
Compliance and Regulatory Certification

Appendix C Utilities

AG Board Locate Utility: blocate
Digital Trunk Status Utility: trunkmon
Show Switch Connections: showcx95

(Page 1 of 1 in this chapter)

tech_support@nmss.com
Copyright © 1999, Natural MicroSystems, Inc. All rights reserved.