(Page 1 of 1 in this chapter) Version

About This Manual

The AG 4000C Installation & Developer's Manual explains how to configure and install an AG 4000C board, and how to verify that it has been installed correctly and is operating correctly. It also provides some general information about developing an application that uses this telephony board.
This manual is targeted to developers of telephony and voice applications who are using the AG 4000C board with CT Access. This manual defines telephony terms where applicable, but assumes that the reader is familiar with telephony concepts, switching, and the C programming language.
This manual is organized as follows: For... See... An overview of the AG 4000C board and related software components, and a summary of the installation process Chapter 1 - Overview of the AG 4000C Board Instructions for configuring the hardware and installing it in your computer Chapter 2 - Installing the Hardware Instructions for editing your AG configuration file so it properly reflects your setup Chapter 3 - Editing the AG Configuration File Verification procedures to check your installation Chapter 4 - Verifying the Installation An overview of T1 and E1 standards, and how the AG 4000C board works with these trunks Chapter 5 - T1 and E1 Trunk Channels An overview of the AG 4000C board's telephony bus connectivity Chapter 6 - AG 4000C Switching A glossary of terms Appendix A - Glossary Specifications for the AG 4000C board and signaling modules Appendix B - Hardware Specifications Details about the board locate utility and the trunk monitor utility Appendix C - Utilities

For...	See...
An overview of the AG 4000C board and related software components, and a summary of the installation process	Chapter 1 - Overview of the AG 4000C Board
Instructions for configuring the hardware and installing it in your computer	Chapter 2 - Installing the Hardware
Instructions for editing your AG configuration file so it properly reflects your setup	Chapter 3 - Editing the AG Configuration File
Verification procedures to check your installation	Chapter 4 - Verifying the Installation
An overview of T1 and E1 standards, and how the AG 4000C board works with these trunks	Chapter 5 - T1 and E1 Trunk Channels
An overview of the AG 4000C board's telephony bus connectivity	Chapter 6 - AG 4000C Switching
A glossary of terms	Appendix A - Glossary
Specifications for the AG 4000C board and signaling modules	Appendix B - Hardware Specifications
Details about the board locate utility and the trunk monitor utility	Appendix C - Utilities

Related Documents

For more information, refer to the following manuals: This manual... Provides... CT Access Developer's Reference Manual An overview of CT Access and a reference of functions, events, reason codes, and errors. CT Access Installation Manual Instructions for installing the software and verifying the installation. Natural Access Installation booklet An overview of the Natural Access CD. AG Runtime Configuration and Developer's Manual Information about the AG configuration file, agmon, AG board and driver error messages, and AG task processors. AG CAS for Natural Call Control Installation and Developer's Manual Information about using AG CAS protocols to perform NCC service call control. Getting Started With MVIP Switching An overview of MVIP-90 and MVIP-95 switching. Hot Swap Developer's Manual An overview of CompactPCI and Hot Swap and how it interfaces to CT Access. Hot Swap Manager Developer's Reference Manual Details about the Hot Swap manager and a reference of the Hot Swap manager library functions. CompactPCI Computer Telephony Specification PICMG 2.5 R1.0 Information about the telephony backplane in CompactPCI, available from PICMG. CompactPCI Specification PICMG 2.0 R2.1 Specification information about CompactPCI, available from PICMG. Enterprise Computer Telephony Forum H.110 Revision 1.0 Hardware Compatibility Specification: CT Bus Information about the H.110 telephony bus, available from ECTF. Hot Swap Specification PICMG 2.1 R1.0 Information about Hot Swap, available from PICMG. IEEE 1101.1, IEEE 1101.10, IEEE 1101.11 Mechanical specifications referenced in CompactPCI specifications.
Refer to the following manuals for information about CT Access services: ADI Service Developer's Manual ADI Service Function Reference Manual Switching Service Developer's Reference Manual Voice Message Service Developer's Reference Manual Natural Call Control Service Developer's Reference Manual
CompactPCI standards and specifications are maintained by the PCI Industrial Computers Manufacturers Group (PICMG). For CompactPCI information, please contact: PICMG c/o Rogers Communications 401 Edgewater Place, Suite 500 Wakefield, MA 01880 Tel: 781-246-9318 Fax: 781-224-1239 Email: www.picmg.org

For GO-MVIP information, please contact: GO-MVIP, Inc. 3220 N Street, NW, Suite 360 Washington, DC 20007 Tel: 800-NOW-MVIP (US and Canada) Tel: 903-769-3717; Fax: 903-769-3818 Email: info@mvip.org

For ECTF information, please contact: ECTF 39355 California Street, Suite 307 Fremont, CA 94538 Tel: 501-608-5915 Fax: 510-608-5917 Email: ectf@ectf.org

This manual...	Provides...
CT Access Developer's Reference Manual	An overview of CT Access and a reference of functions, events, reason codes, and errors.
CT Access Installation Manual	Instructions for installing the software and verifying the installation.
Natural Access Installation booklet	An overview of the Natural Access CD.
AG Runtime Configuration and Developer's Manual	Information about the AG configuration file, `agmon`, AG board and driver error messages, and AG task processors.
AG CAS for Natural Call Control Installation and Developer's Manual	Information about using AG CAS protocols to perform NCC service call control.
Getting Started With MVIP Switching	An overview of MVIP-90 and MVIP-95 switching.
Hot Swap Developer's Manual	An overview of CompactPCI and Hot Swap and how it interfaces to CT Access.
Hot Swap Manager Developer's Reference Manual	Details about the Hot Swap manager and a reference of the Hot Swap manager library functions.
CompactPCI Computer Telephony Specification PICMG 2.5 R1.0	Information about the telephony backplane in CompactPCI, available from PICMG.
CompactPCI Specification PICMG 2.0 R2.1	Specification information about CompactPCI, available from PICMG.
Enterprise Computer Telephony Forum H.110 Revision 1.0 Hardware Compatibility Specification: CT Bus	Information about the H.110 telephony bus, available from ECTF.
Hot Swap Specification PICMG 2.1 R1.0	Information about Hot Swap, available from PICMG.
IEEE 1101.1, IEEE 1101.10, IEEE 1101.11	Mechanical specifications referenced in CompactPCI specifications.

(Page 1 of 1 in this chapter) Version

tech_support@nmss.com